Eighth Edition • First Printing
Operator's Manual
Inspections
Part No. 1311642GT
Z
®
-45/25J
39
39
Retract the primary boom to the stowed
position or drive in the opposite direction.
Result: The machine should drive.
40
Return to level ground and stow the boom.
41
With the boom fully stowed, drive the machine
onto a slope where the chassis pitch angle is
greater than 2.5°.
Result: The machine should continue to drive.
42
Return to level ground and raise the
secondary boom to an out of stowed position
(approximately 15° above horizontal).
43
Drive the machine onto a slope where the
chassis pitch angle is greater than 2.5°.
Result: The machine should stop once the
machine reaches 2.5° of chassis tilt and the
alarm should sound at the platform controls.
44
Lower the secondary boom to the stowed
position or drive in the opposite direction.
Result: The machine should drive.
45
With the boom fully stowed, drive the machine
onto a slope where the chassis pitch angle is
greater than 2.5°.
Result: The machine should continue to drive.
46
Return to level ground and raise the primary
boom to an out of stowed position
(approximately 10° above horizontal).
47
Drive the machine onto a slope where the
chassis roll angle is greater than 4.5°.
Result: The machine should stop once the
machine reaches 4.5° of chassis tilt and the
alarm should sound at the platform controls.
48
Lower the primary boom to the stowed position
or drive in the opposite direction.
Result: The machine should drive.
49
Return to level ground and extend the primary
boom approximately 1.6 ft / 0.5 m.
50
Drive the machine onto a slope where the
chassis roll angle is greater than 4.5°.
Result: The machine should stop once the
machine reaches 4.5° of chassis tilt and the
alarm should sound at the platform controls.
51
Retract the primary boom to the stowed
position or drive in the opposite direction.
Result: The machine should drive.
52
Return to level ground and stow the boom.
53
With the boom fully stowed, drive the machine
onto a slope where the chassis roll angle is
greater than 4.5°.
Result: The machine should continue to drive.
54
Return to level ground and raise the
secondary boom to an out of stowed position
(approximately 15° above horizontal).
55
Drive the machine onto a slope where the
chassis roll angle is greater than 4.5°.
Result: The machine should stop once the
machine reaches 4.5° of chassis tilt and the
alarm should sound at the platform controls.
56
Lower the secondary boom to the stowed
position or drive in the opposite direction.
Result: The machine should drive.
Содержание Genie Z-45/25J Bi-Energy
