Terex Genie SX-105 XC Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 76

background image

First Edition • Third Printing

Operator's Manual

Work Area Safety

Part No. 1270327GT

SX

™

-105 XC

™

• SX

™

-125 XC

™

11

Wor k Ar ea Saf et y

Electrocution Hazards

This machine is not electrically insulated and will
not provide protection from contact with or
proximity to electrical current.

Obey all local and
governmental regulations
regarding required
clearance from electrical
power lines. At a minimum,
the required clearance
contained in the chart
below must be followed.

Line Voltage

Required Clearance

0 to 50KV

3.05 m

50 to 200KV

4.60 m

200 to 350KV

6.10 m

350 to 500KV

7.62 m

500 to 750KV

10.67 m

750 to 1000KV

13.72 m

Allow for platform movement, electrical line sway
or sag, and beware of strong or gusty winds.

Keep away from the
machine if it contacts
energized power lines.
Personnel on the ground
or in the platform must
not touch or operate the
machine until energized
power lines are shut off.

Do not operate the machine during lightning or
storms.

Do not use the machine as a ground for welding.

Tip-over Hazards

Occupants, equipment and materials shall not
exceed the maximum platform capacity for the
restricted or unrestricted range of motion.

Maximum platform capacity
Unrestricted range of motion

300 kg

Maximum occupants

2

Maximum platform capacity
Restricted range of motion

454 kg

Maximum occupants

3

If the restricted range of motion is selected for the
maximum platform capacity, do not move the
platform into the unrestricted range of motion
zone.

Do not exceed the selected maximum platform
capacity.

Do not attach a platform rated at 300 kg
(unrestricted range of motion) or 454 kg (restricted
range of motion) to machines with any other rated
load. See the serial label for the maximum rated
load.

«
...
11
12
13
14
15
...
»

Содержание Genie SX-105 XC













































































Отзывы:

Нет отзывов

Похожие инструкции для Genie SX-105 XC

Бренд: GMG Страницы: 8

Бренд: POP UP Страницы: 36

Бренд: WERNERCO Страницы: 36

Genie GTH4018 SR

Бренд: Terex Страницы: 121

Бренд: Terex Страницы: 301

EHLTX-3653-1-39

Бренд: Vestil Страницы: 32

Бренд: SICE Страницы: 54

Бренд: CLAS Страницы: 32

Бренд: Airo Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды