Terex Genie GS-2669 BE Скачать руководство пользователя страница 68

Страница: 68 / 205

Service Manual

May 2015

Platform Components

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

9 Carefully lift the platform enough to clear the

platform pivot.

10 Slide the platform towards the non-steer end

of the machine until the slider blocks are

visible underneath the slider block channel.

11 Carefully lift the platform off of the machine

and place it on a structure capable of

supporting it.

Crushing hazard. The platform

will become unbalanced and fall

it not properly supported.

Note: Note the position of the slider blocks before

the platform is removed so that when the platform

is installed they will be in the correct position.

2-2

Platform Extension Deck

How to Remove the Platform

Extension Deck

1 Remove the retaining fasteners from the deck

catch and remove the deck catch.

2 Remove the retaining fasteners from the deck

stop and remove the deck stop.

3 Repeat steps 1 and 2 for the other side of the

platform.

1 deck catch
2 deck stop

4 Remove the platform controls from the

platform.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды