Terex Genie GS-2669 BE Скачать руководство пользователя страница 66

Страница: 66 / 205

Service Manual

May 2015

Platform Controls

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

1-4

Platform Emergency Stop Button

How to Remove the Platform

Controls Emergency Stop Button

1 Push in the red Emergency Stop button to the

off position at both the ground and platform

controls.

2 Disconnect the platform controls from the

control cable at the platform.

3 Remove the fasteners securing the platform

control box to the platform control bracket.

4 Remove the fasteners securing the bottom

cover to the platform control box. Open the

control box.

5 Disconnect the white wires from the

Emergency Stop base.

Electrocution/burn hazard.

Contact with electrically charged

circuits could result in death or

serious injury. Remove all rings,

watches and other jewelry.

Component damage hazard.

Electrostatic discharge (ESD)

can damage printed circuit board

components. Maintain firm

contact with a metal part of the

machine that is grounded at all

times when handling printed

circuit boards OR use a

grounded wrist strap.

6 Carefully remove the Emergency Stop base

from the Emergency Stop button.

7 Carefully remove the retaining ring from the

Emergency Stop button.

8 Carefully remove the Emergency Stop button

from the platform control box.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды