background image

T5e ec--H2O Kit

KIT NO. 9006828

Page 1 of 9

t

9006829 Rev. 00 (12--09)

Tennant Company

Customer Service: (800) 553--8033 or (763) 513--2850

This kit includes the parts needed to convert a standard model over to an ec--H2O

t

model.

INSTALLATION INSTRUCTIONS:

Installation Time: 4--6 Hours
Special Tools Required: None

PREPARE MACHINE FOR KIT INSTALL:

1. Drain the solution and recovery tanks.

2. Park the machine on a level surface, lower the

scrub head and remove the key.

3. Remove the scrub head assembly from the

machine (Figure 1).

FOR SAFETY: Before removing the scrub head

assembly, disconnect the battery cables.

Disk Model

shown

Fig. 1

4. Remove the batteries from the machine

(Figure 2).

FOR SAFETY: When handling batteries, wear pro-

tective gloves and eye protection. Avoid contact

with battery acid.

Fig. 2

INSTALL

ec- H2O

WIRE HARNESS:

1. Remove the cover the from the circuit breaker box

and install

ec--H2O

wire harness [p/n 1055447]

(Figure 3).

Circuit

Breaker

Cover

Fig. 3

2. Starting from inside the circuit breaker box,

connect the following

ec--H2O

harness wires as

described in steps 3, 4 and 5 (Figure 4).

Relay

[p/n 1012216]

Red 1z

Black 13u/13T/13z/13s

Fig. 4

3. Connect red wire (1z) to the brush contactor

terminal and the black wires (13u/13T/13z/13s) to

the ground stud (Figure 5).

Red 1z

Black 13u/13T/13z/13s

Fig. 5

Home

Find...

Go To..

Содержание T5e ec-H2O 9006828










Отзывы: