background image

8  

II. Melt the solder 

1. 

Apply the nozzle to the soldered part and melt the solder. 

 

Do not touch nozzle to board. 

2. 

Try to check the inside of the hole and the backside of the PCB 

if solder is melted. 

3. 

Try moving the solder using the desolder gun nozzle, if it moves 

easily then it means that solder is completely melted but do not 

force it. 

 

III. Absorb the solder 

1. 

After checking that solder is completely melted, position the 

desolder gun then absorb the solder by pulling  the trigger. 

 

* Be careful not to leave any solder remain in the hole.

 

2. 

After fully absorbing all the solder, cool the soldering junction in 
order to prevent it from becoming resoldered. 

 

 

OPERATION GUIDELINES 

5  

● 

Compact unit with air cylinder type strong suction vacuum 

pump. 

● 

Suited for multi-layered PCB reworking. 

● 

The heating element and tip are designed closely to 

guarantee enough temperature during desoldering. 

 
FEATURES 

 

SPECIFICATIONS 

Power Input : 

Available in 110V / 220V 

Power Consumption: 

80W (Max) 

Temperature Range: 

150°C - 380°C 

Heating Element: 

Heating Element 

Output Voltage: 

24V 

Tip to Ground Resistance: 

Below 2 Ω 

Tip to Ground Potential: 

Below 2mV 

Suction Flow: 

15 l /min (max) 

Vacuum Generator: 

Double Cylinder 

Vacuum Pressure: 

600mm Hg 

Station Dimensions: 

7.4” x 5” x9.6” 

Weight: 

11.7 lbs. 

Содержание 21-19700







Отзывы: