background image

This appliance can be used by children aged form 8 years and above and persons 
with  reduced  physical,  sensory  or  mental  capabilities  or  lack  of  experience  and 
knowledge  if  they  have  been  given  supervision  or  instruction  concerning  use  of 
the appliance in a safe way and understand the hazards involved. Children shall 
not play with the appliance. Cleaning and user maintenance shall not be made by 
children without supervision. 
 
The specific instructions related to the safe operation of this appliance (as given in 
7.12  of  this  standard)  shall  be  collated  together  in  the  front  section  of  the  user 
instructions. 
The  height  of the  characters, measured on  the capital  letters,  shall  be at least  3 
mm. 
These instructions shall also available in an alternative format, e.g. on a website. 

 

A fire may result if the appliance is not used with care, therefore: 

→ 

be careful when using the appliance in places where there are combustible 
materials ; 

→ 

do not apply to the same place for a long time; 

→ 

do not use in presence of an explosive atmosphere; 

→ 

be aware that heat may be conducted to combustible materials that are out 
of sight; 

→ 

place the appliance on its stand after use and allow it to cool down before                                             
storage; 

→ 

do not leave the appliance unattended when it is switched on. 

 

Rohs  

 

Correct Disposal of this product 

This marking indicates that this product should not be disposed 
with other household wastes throughout the EU. To prevent pos-
sible harm to the environment or human health from uncon-
trolled waste disposal, recycle it responsibly to promote the sus-
tainable reuse of material resources. To return your used device, 
please use the return and collection systems or contact the re-
tailer where the product was purchased. They can take this 
product for environmental safe recycling.

 

 

 

www.Tenma.com 

 

   

 

Instruction Manual

 

Thank you for purchasing the  21-19650 Soldering Station. 

Please read the manual before using the unit. 

Keep manual in accessible place for future reference. 

Soldering Station

 

 

21

21

-

-

19650

19650

 

 

Содержание 21-19650









Отзывы: