19
NOI
TC
UD
OR
TNI
TN
AT
RO
PMI
SN
OIT
UA
CE
RP
ER
OF
EB
NI
GE
B
UO
Y
LLI
MD
AE
RT
NOI
TA
RE
PO
GNI
NOI
TI
DN
OC
SE
NIL
EDI
UG
GNI
TO
OH
SEL
BU
OR
T
EC
NA
NET
NIA
M
&
DET
IMI
L
YT
NA
RR
A
W
T940 OM 060506'.indd 19
2006/6/6 8:23:51 AM
Cleanliness of your treadmill and its operation environment will keep maintenance problems and service calls to a
minimum. For this reason, we recommend that the following preventive maintenance schedule be followed.
AFTER EACH USE (DAILY)
Clean and inspect, following these steps:
• Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
• Wipe down the running belt, deck, motor cover, and console casing with a damp cloth. Never use solvents, as
they can cause damage to the treadmill.
• Inspect the power cord.
• Make sure the power cord is not underneath the treadmill or in any other area where it can become pinched or
cut.
• Check the tension and alignment of the running belt. Make sure that the treadmill belt will not damage any other
components on the treadmill by being misaligned.
EVERY WEEK
Clean underneath the treadmill, following these steps:
• Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
• Fold the treadmill into the upright position, making sure that the lock latch is secure.
• Move the treadmill to a remote location.
• Wipe or vacuum any dust particles or other objects that may have accumulated underneath the treadmill.
• Return the treadmill to its previous position.
EVERY MONTH - IMPORTANT!
• Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
• Inspect all assembly bolts of the machine for proper tightness.
• Turn off the treadmill and wait 60 seconds.
• Remove the motor cover. Wait until ALL LED lights turn off.
• Clean the motor and lower board area to eliminate any lint or dust particles that may have accumulated. Failure
to do so may result in premature failure of key electrical components.
• Vacuum and wipe down the belt with a damp cloth. Vacuum any black/white particles that may accumulate
around the unit. These particles may accumulate from normal treadmill use.
EVERY 6 MONTHS OR 150 MILES
It is necessary to lubricate your treadmill running deck every six months or 150 miles to maintain optimal performance.
Once the treadmill reaches 150 miles, the console will display the message “LUBE” or LUBE BELT”. The treadmill will
not operate while the message is showing. Hold Stop for 5 seconds to suspend message for 5 miles. Your treadmill
came with a bottle of lubricant which can be used for two applications.
• Turn off the treadmill with the on/off switch, then unplug the
power cord at the wall outlet.
• Loosen both the rear roller bolts. (For best results, place two
removable marks on both sides of the frame and note roller
position). Once the belt is loosened, take the bottle of lubricant
and apply it to the entire top surface of the running deck. Tighten
both rear roller bolts (matching up the marks for proper position)
to original position. After you have applied lubricant, plug in the
power cord, insert the safety key, start the treadmill and walk on
the belt for two minutes to spread the lubricant.
• Lubricate the air shocks with Teflon based spray.
• Once lubrication is complete, reset the console by pressing and
holding ‘STOP’ and Speed ‘+’ buttons for 5 seconds.
MAINTENANCE
RUNNING BELT
RUNNING DECK
