Telular PHONECELL SX3e AMPS Скачать руководство пользователя страница 5

Страница: 5 / 26

Installation Summary

HONECELL

SX3e AMPS

SER

ANUAL

Step 1. Choose an Antenna Location (pg. 6-7)

••

Choose a location.

••

Next, connect power to the
FWT and turn the unit ON.

••

Then, connect the antenna

(not supplied)

••

Check the cellular signal strength and
move the antenna until you achieve the
best signal possible.

Step 2. Plug In Your Phone (page 8)

••

Once the antenna is connected, hook up
a phone.

••

Then, make a test call to check noise levels,
and adjust the antenna location accordingly.

••

NOTE: If your

Phonecell SX3e

is not pre-pro-

grammed for NAM

(Number Assignment Module)

information, you’ll need to perform the
NAM/Phone Number Setup in Step 3. Then, return
to this step (2).

••

Plug in additional phones, Fax and/or Modem.

Step 3. NAM/Phone Number Setup (pg. 9-11)

••

If your

Phonecell

was not pre-programmed for

NAM information, you need to perform the
NAM/Phone Number Setup procedure.

••

Otherwise, continue to Step 4.

Step 4. Wall or Desk Installation (pg. 12-13)

••

After you’ve selected a location and made all
the necessary connections and adjustments,
your

Phonecell SX3e

is ready for either

wall-mounting or desktop/tabletop use.

There are four steps to installing the

Phonecell SX3e

FWT properly.

These steps are summarized below and explained in detail in the
remainder of this manual.

Содержание PHONECELL SX3e AMPS



























Результаты поиска

Содержание PHONECELL SX3e AMPS

Отзывы:

Похожие инструкции для PHONECELL SX3e AMPS

Бренды по названию

Популярные бренды

Telular PHONECELL SX3e AMPS, Руководство пользователя

Результаты поиска

Содержание PHONECELL SX3e AMPS

Отзывы:

Похожие инструкции для PHONECELL SX3e AMPS

Бренды по названию

Популярные бренды