background image

 

10 

FMB640| 

Wiki

 

Mounting recommendations 

 

Connecting Wires 

 

Wires should be connected while module is not plugged in. 

 

Wires should be fastened to the other wires or non-moving 
parts. Try to avoid heat emitting and moving objects near 
the wires. 

 

The connections should not be seen very clearly. If factory 
isolation was removed while connecting wires, it should be 
applied again. 

 

If the wires are placed in the exterior or in places where they 
can be damaged or exposed to heat, humidity, dirt, etc., 
additional isolation should be applied. 

 

Wires cannot be connected to the board computers or 
control units. 

 

Connecting power source 

 

Be sure that after the car computer falls asleep, power is still 
available on chosen wire. Depending on car, this may 
happen in 5 to 30 minutes period. 

 

When module is connected, be sure to measure voltage 
again if it did not decrease. 

 

It is recommended to connect to the main power cable in 
the fuse box. 

 

Use 3A, 125V external fuse. 

 

 

 
 

 

Connecting ignition wire 

 

Be sure to check if it is a real ignition wire 

 power does not 

disappear while starting the engine. 

 

Check if this is not an ACC wire (when key is in the first 
position, most electronics of the vehicle are available). 

 

Check if power is still available when you turn off any of 
vehicles devices. 

 

Ignition is connected to the ignition relay output. As 
alternative, any other relay, which has power output, when 
ignition is on, may be chosen. 

 

Connecting ground wire

 

 

Ground wire is connected to the vehicle frame or metal 
parts that are fixed to the frame.

 

 

If the wire is fixed with the bolt, the loop must be connected 
to the end of the wire.

 

 

For better contact scrub paint from the place where loop is 
connected.

 

 

PAY ATTENTION! Connecting the power supply must be 
carried out in a very low impedance point of on-board 
vehicle network. Connecting the GND at an arbitrary 
point to the mass of the car is unacceptable, as static 
and dynamic potentials on the line GND will be 
unpredictable, which can lead to unstable FMB640 
operation and even its failure.

 

Содержание FMB640

















Отзывы: