Telit Wireless Solutions ME310G1-W1 Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 96

background image

ME310G1 Hardware Design Guide

1VV0301588 Rev. 12

Page 90 of 96

2021-06-14

Trademarks

TELIT and the Stylized T-Logo are registered in the Trademark Office. All other product
or service names are property of their respective owners.

3rd Party Rights

The software may include 3rd Party’s software Rights. In this case the user agrees to
comply with all terms and conditions imposed in respect of such separate software
rights. In addition to 3rd Party Terms, the disclaimer of warranty and limitation of liability
provisions in this License, shall apply to the 3rd Party Rights software as well.

TELIT HEREBY DISCLAIMS ANY AND ALL  WARRANTIES EXPRESSED OR IMPLIED FROM
ANY  3RD  PARTY  REGARDING ANY SEPARATE FILES, ANY 3RD  PARTY  MATERIALS
INCLUDED IN THE SOFTWARE, ANY 3RD  PARTY  MATERIALS FROM WHICH THE
SOFTWARE IS DERIVED (COLLECTIVELY “OTHER CODES”), AND THE USE OF ANY OR ALL
OTHER CODES  IN CONNECTION WITH THE SOFTWARE, INCLUDING (WITHOUT
LIMITATION) ANY WARRANTIES OF SATISFACTORY QUALITY OR FITNESS FOR A
PARTICULAR PURPOSE.

NO 3RD PARTY LICENSORS OF OTHER CODES MUST BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING WITHOUT LIMITATION LOST OF PROFITS), HOWEVER CAUSED AND
WHETHER MADE UNDER CONTRACT, TORT OR OTHER LEGAL THEORY, ARISING IN ANY
WAY OUT OF THE USE OR DISTRIBUTION OF THE OTHER CODES OR THE EXERCISE OF
ANY RIGHTS GRANTED UNDER EITHER OR BOTH THIS LICENSE AND THE LEGAL TERMS
APPLICABLE TO ANY SEPARATE FILES, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.

Waiver of Liability

IN NO EVENT WILL TELIT AND ITS AFFILIATES BE LIABLE FOR AY DIRECT, INDIRECT,
SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY
INDIRECT DAMAGE OF ANY KIND WHATSOEVER, INCLUDING BUT NOT LIMITED TO
REIMBURSEMENT OF COSTS, COMPENSATION OF ANY DAMAGE, LOSS OF
PRODUCTION, LOSS OF PROFIT, LOSS OF USE, LOSS OF BUSINESS, LOSS OF DATA OR
REVENUE, WHETHER OR NOT THE POSSIBILITY OF SUCH DAMAGES COULD HAVE BEEN
REASONABLY FORESEEN, CONNECTD IN ANY WAY TO THE USE OF THE PRODUCT/S OR
TO THE INFORMATION CONTAINED IN THE PRESENT DOCUMENTATION, EVEN IF TELIT
AND/OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES
OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY.

«
...
88
89
90
91
92
...
»

Содержание ME310G1-W1

































































































Отзывы:

Нет отзывов

Похожие инструкции для ME310G1-W1

Ubigate iBG1000

Бренд: Samsung Страницы: 52

Connect Home Pro ET-WV530

Бренд: Samsung Страницы: 2

Бренд: TRENDnet Страницы: 36

Бренд: Y!mobile Страницы: 2

Бренд: Deliberant Страницы: 69

Бренд: MikroTik Страницы: 4

Бренд: TRENDnet Страницы: 58

Бренд: ZyXEL Communications Страницы: 263

Бренд: Ubiquiti Страницы: 20

Бренд: Bosslan Страницы: 4

Бренд: EnGenius Страницы: 84

Бренд: HPE Страницы: 4

Бренд: THOMSON Страницы: 54

Бренд: Ubiquiti Страницы: 3

Бренд: Ubiquiti Страницы: 5

Бренд: Ubiquiti Страницы: 44

Wireless Router

Бренд: Linksys Страницы: 6

SMK-Link VP6494

Бренд: Interlink electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды