manualshive.com logo in svg

Telit Wireless Solutions GS2101M Series, Справочник по командам, Страница: 84 / 196

Поделиться
Скачать
Telit Wireless Solutions GS2101M Series Скачать руководство пользователя страница 84

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

 Rev. 2.0

84

2019-08-05

Example 

AT+WSYNCINTRL=500

 If 500 consecutive beacons are missed then, SYNC loss is detected and GS node sends the 
Disassociation packet to the Access Point.

The time taken for detecting sync loss in this case is approximately 50seconds (500 
*100msec).

5.1.5 Set RTS Threshold

This command is used to set the RTS threshold value.

Command Syntax

AT+WRTS=<RTSTHRESHOLD>[,TXOP ENABLE]

Parameter Description

Table 56, page 84

 describes the RTS Threshold parameters.

Synchronous Response

Table 57, page 85

 describes the synchronous responses and remarks for the RTS Threshold 

command.

Table 55   Sync Loss Interval Asynchronous Responses

Responses

Remarks

314Disassociation Event
Where,
Subtype - 3
Length - 14 (ASCII equivalent decimal is 20 characters, i.e., 
length of the actual message)
Actual message - Disassociation Event
The type of message. Length is 1 byte. for asynchronous 
message, it is 0x41 (ASCII value A).

GS node does not receive beacons for this time 
informs the user with this message.

Note: 

<ESC>

 and 

Type

 is not displayed because its Tera Term issue.

Table 56   RTS Threshold Parameters

Parameter

Optional/Mandatory

Value

Description

RTSTHRESHOLD Mandatory

0 to 2999 
Default value - 0

This parameter specifies the RTS/CTS 
threshold. 
When this parameter is set to one of the 
values from 0 to 2999, it is considered as 
RTS threshold.

Note: 

   When this parameter is set to a 

value >=3000, self CTS is enabled.

TXOP ENABLE Optional

N/A

Reserved for future use.

Содержание GS2101M Series





































































































































































































Отзывы:

Нет отзывов