manualshive.com logo in svg

Telit Wireless Solutions GS2101M Series, Справочник по командам, Страница: 65 / 196

Поделиться
Скачать
Telit Wireless Solutions GS2101M Series Скачать руководство пользователя страница 65

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

 Rev. 2.0

65

2019-08-05

4.3.2 Save Profile

This command is used to save the current profile. Upon deployment of this command, the 
current configuration settings are stored in non-volatile memory under the specified profile, 
(profile 0, or profile 1). In order to ensure that these parameters are restored after power 
cycling the GS node, the command AT&Y must also be issued, using the same profile 
number selected here. 

Command Syntax

AT&Wn

Parameter Description

Table 30, page 65

 describes the Save Profile parameters.

Synchronous Response

Table 31, page 65

 describes the synchronous responses and remarks for the Save Profile 

command.

Table 30   Save Profile Parameters

Parameter

Optional/Mandatory

Value

Description

n

Mandatory

0

For profile 0

1

For profile 1

Saves the profile specified by 

n

 (0 or 1). 

Table 31   Save Profile Synchronous Responses

Responses

Remarks

OK

Success

ERROR:INVALID INPUT

If parameters are not valid.
(

n

 value is other than 0 or 1)

NOTE:  

GS node supports two profiles.

Содержание GS2101M Series





































































































































































































Отзывы:

Нет отзывов