Telit Wireless Solutions EVK Series Скачать руководство пользователя страница 6

Страница: 6 / 49

Telit EVK4

HW User Guide\

0805 Rev. 6

Page

2017-05-19

ADD-ON BOARDS ..................................................................... 16

Texas Instruments Launchpad .................................................... 16

Raspberry Pi2 / Pi3 ..................................................................... 17

Arduino ....................................................................................... 18

5.3.1.

Arduino UNO Form Factor Boards .............................................. 18

JUMPERS CONFIGURATION ................................................... 21

Principal Modes of Operation ...................................................... 21

6.1.1.

Standalone Mode.

PL203 Jumper

............................................. 21

6.1.2.

Booster Pack Mode.

PL203 Jumper

.......................................... 21

I²C Bus ....................................................................................... 22

UART1 (xE910 USIF0) ............................................................... 23

Push Switch1 -

SW203

............................................................... 24

Push Switch2

–

SW202

.............................................................. 24

Potentiometer1

–

POT1

.............................................................. 25

Booster Pack ADC VREF ........................................................... 26

OPTICAL INDICATORS ............................................................. 27

LEDs description ......................................................................... 27

Programmable LEDs .................................................................. 28

Charge Status LED ..................................................................... 28

SENSORS .................................................................................. 29

I²C Bus ....................................................................................... 29

List of Sensors, Battery Monitor .................................................. 29

Sensor Interrupt Lines................................................................. 29

MISCELANEOUS ....................................................................... 30

Potentiometers ........................................................................... 30

Push-Button Switches ................................................................. 30

10.

UART1 (USIF0) .......................................................................... 31

11.

STANDALONE\BUNDLING JUMPER CONFIGURATION ......... 32

12.

SCHEMATICS ............................................................................ 34

13.

CONFORMITY ASSESSMENT ISSUES .................................... 44

FCC/IC Regulatory notices ......................................................... 44

14.

SAFETY RECOMMENDATIONS................................................ 45

READ CAREFULLY .................................................................... 45

Содержание EVK Series


















































Результаты поиска

Содержание EVK Series

Отзывы:

Похожие инструкции для EVK Series

Бренды по названию

Популярные бренды

Telit Wireless Solutions EVK Series, Руководство пользователя

Результаты поиска

Содержание EVK Series

Отзывы:

Похожие инструкции для EVK Series

Бренды по названию

Популярные бренды