TELink 1250i Скачать руководство пользователя страница 4

Connection Instructions 

 

1. Turn the power switch OFF.  Plug the included power supply into a normal 

110VAC wall outlet, and the opposite end into the TELink

®

 1250i.  Only use 

the power pack provided with the unit (12VDC, center pin positive). Many 
power supplies look alike, but provide different output. Using the wrong one 
voids your warranty and may damage the unit.   

 

2.  Connect the audio output jack to the external audio system input using a 

mono RCA-to-RCA cable (included). If the external audio system does not 
have an RCA-style input, use the included RCA to 1/8 inch adapter.  Be sure 
to select the right impedance before turning the unit on. 

 

3. NOT REQUIRED FOR OMNI-Connect the BGM using a mono RCA-to-RCA 

cable (included). If the BGM source does not have an RCA-style output, use 
the included RCA to 1/8 inch adapter.  This step is optional and only required 
if you are using Background Music. 

 

4.  Connect the Ethernet jack to your Local Area Network. (LAN)  The unit is 

factory DHCP enabled and should obtain an IP address automatically.  See 
the local Network Administrator or the Quick Install Guide on the back page of 
this manual for assistance. 

 

5.  Turn the unit on. 

 

6. Call Omni to confirm connectivity between the unit and their server(s) 

via the Internet. 

 
Step 2 – Adjust Volume 

 

The Volume buttons on the front of the unit are used to adjust the Volume to a 
comfortable listening level. 
  

TELink 1250i

                                9                                        8/17/2004 

Содержание 1250i








Отзывы: