Telguard TG-7 Series Скачать руководство пользователя страница 35

Страница: 35 / 42

TG-7 Cellular Series Installation & Operating Guide

AC Terminal Strip Pin Assignments

Terminal
Strip Pin

Definition

Connects To

Function

Status LED Reference

1 AC

2 AC

AC Power
input

Provided AC
adapter (120V,
160mA)

Provides power to
communicator and
battery-charging circuit.

Power LED 8 ON when AC is
normal, OFF and STC LED 2
flashes 1 time when AC is low.

Compatible Alarm Panels

Any UL/ULC/cUL Listed alarm panel that supports one of the following formats is compatible and
may be used with the TG-7FE:

•

Pulse Formats:

3+1 pulse; 10pps, Double Round, 1400 Hz ack

3+1 pulse; 20pps, Double Round, 2300 Hz ack

3+1 pulse; 40pps, Double Round, 2300 Hz ack

4+2 pulse; 20pps, Double Round, 1400 Hz ack

4+2 pulse; 20pps, Double Round, 2300 Hz ack

4+2 pulse; 40pps, Double Round, 2300 Hz ack

•

Contact ID

•

Modem IIe/IIIa

•

SIA2 (SIA-DC-03 level 2 release at 300 baud)

•

Sonitrol

•

DMP

The installer should verify compatibility at the time of installation.

Hexadecimal account numbers can be used with 3+1 or 4+2 formats, as well as Contact ID and Modem (4
or 10 digits for Contact ID, 4 digits for Modem).

UL Compliance Note:

While TG-7 Cellular Series communicators support the above formats, some formats

may not meet the requirements for fire systems set in UL 864. Contact ID and SIA2 are the only formats
identified as complying beginning with UL 864 10

Edition. If in doubt, check with your AHJ

Содержание TG-7 Series











































Результаты поиска

Содержание TG-7 Series

Отзывы:

Похожие инструкции для TG-7 Series

Бренды по названию

Популярные бренды

Telguard TG-7 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TG-7 Series

Отзывы:

Похожие инструкции для TG-7 Series

Бренды по названию

Популярные бренды