Telex Audiocom SS-1002 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 28

Telex Audiocom SS-1002 Скачать руководство пользователя страница 22

18

Specifications

General

Power Requirements

Phantom Power: +24VDC nominal, 75mA without
speaker; 700mA with Speaker
Local Power: +15VDC, 75mA without speaker;
700mA with Speaker

Dimensions

See Dimensions Drawings (Figure 11 on page 19)

Environmental Requirements

Storage:
-20° C to 80° C; 0% to 95% RH, non-condensing
Operating:
0° C to 50° C; 0% to 95% RH, non-condensing

Dynamic-mic Headset/Handset

Microphones

50 to 200 Ohms, dynamic (balanced or unbalanced)

Headphones

150 to 600 Ohm, monaural

Connector Type: XLR-4M

Pin 1 - Microphone Low
Pin 2 - Microphone High
Pin 3 - Headphone High
Pin 4 - Headphone Low

Panel Microphone

Built-in Microphone

2.2k Ohms, electret (44mV nominal),
Omnidirectional

Gooseneck Microphone

Connector Type: 1/4” Threaded TRS, 5k Ohms,
electret (44mV nominal)

Tip         Microphone High (+12VDC)
Ring        Common
Sleeve     Common
Compatible with MCP-90 Series Microphones

Intercom Channels, Balanced Mode
(SW1 set to BAL position)

Output Level

1V

RMS

nominal

Input Impedance

300 Ohms

Bridging Impedance

greater than 5k Ohms

Sidetone

20dB adjustable range

Call Signaling

Send

20kHz ±100Hz, 0.5V

RMS

±10%

Receive

20kHz ±800Hz, 100mV

RMS

Mic Kill Detect Frequency

24kHz ±800Hz, 100mV

RMS

Noise Contribution

less than -70dB

Common Mode Rejection Ratio

greater than 50dB

Connector Type:
Six-position push type terminal block

Pin 1 - Audio and DC Common
Pin 2 - Local power (+12 to +15VDC), if needed
Pin 3 - Intercom CH1 audio low and +24VDC power
Pin 4 - Intercom CH1 audio high and +24VDC power
Pin 5 - Intercom CH2 audio low and +24VDC power
Pin 6 - Intercom CH2 audio high and +24VDC power

Intercom Channels, Unbalanced Mode
(SW1 set to UNBAL position)

Output Level

0.775V

RMS

±10%

Input Impedance

200 Ohms

Bridging Impedance

greater than 5k Ohms

Sidetone

-40dB, 20dB adjustable range

Connector Type:
Six-position push type terminal block

Pin 1 - Ground
Pin 2 - +30VDC
Pin 3 - CH B Intercom
Pin 4 - CH A Intercom
Pin 5 - NC
Pin 6 - NC

Speaker Output Power

4W max @ 8 Ohms

«
...
20
21
22
23
24
...
»

Содержание Audiocom SS-1002





























Отзывы:

Нет отзывов