Telex Audiocom PS2000L Скачать руководство пользователя

Страница: 11 / 16

Specifications

General

Input Power Requirements:

100 to 240 VAC, 50 / 60 Hz

Output Power (each channel)

1 VDC, 2A

Dimensions: 1.75" (44.5 mm) high x 8.25" (209.5 mm) wide x 10.31" (261.9 mm) deep
Weight: approximately 2.5 lb (1.13 kg)
Environmental Requirements:

Storage: -20

C to 80

C; 0% to 95% humidity, non-condensing

Operating: 0

C to 50

C; 0% to 95% humidity, non-condensing

Intercom Channels

General

Connector Type: One XLR-3M audio connector for each channel. Pin-out depends on setting
of internal switch S200 for balanced or unbalanced operation as defined below.

Balanced Mode (S200 set to BAL position)

Line Terminating Impedance: 300 ohms

10%

Connector Pin-out

Pin 1

Common (audio and DC return)

Pin 2

Full-duplex, balanced intercom audio and +24 VDC output

Pin 3

Full-duplex, balanced intercom audio and +24 VDC output

Unbalanced Mode (S200 set to UNBAL position)

Line Terminating Impedance: 150 ohms

Connector Pin-out

Pin 1

Common (audio and DC return)

Pin 2

+24 VDC output

Pin 3

Full-duplex, unbalanced Intercom audio high

Approvals

UL, CUL, CE

1 1

Содержание Audiocom PS2000L

















Результаты поиска

Содержание Audiocom PS2000L

Отзывы:

Похожие инструкции для Audiocom PS2000L

Бренды по названию

Популярные бренды

Telex Audiocom PS2000L, Инструкция пользователя

Результаты поиска

Содержание Audiocom PS2000L

Отзывы:

Похожие инструкции для Audiocom PS2000L

Бренды по названию

Популярные бренды