background image

 

NOTIFICATION TO THE TELEPHONE COMPANY  

Before you may connect your telephone you must notify the telephone company of particular line(s)to which such connections is to be made, and provided to 
the telephone company the FCC registration number and ringer equivalence number of the registered protective circuitry. The customer shall give notice to 
the telephone company upon final disconnection of such equipment or circuitry from the particular line(s).  
 

MALFUNCTION OF TELEPHONE  

In the event that your telephone fails to work properly during your ownership and use of it, you should disconnect it from the telephone line to determine if it is 
your phone which is not working properly or if it is problem in the telephone company's network. If the problem is with your telephone you should  
discontinue its use until it is repaired.  
 

TELEPHONE CONNECTION REQUIREMENTS  

Except for telephone company provided ringers, all connections to the telephone network shall be made through standard telephone company provided jacks, 
in such a manner as to allow for easy and immediate disconnection of the terminal equipment. Standard jacks shall be so arranged that if the plug  
connected thereto is withdrawn, no interference to the operation of the equipment at the customer's premises which remains connected to the telephone net 
work shall occur by reason of such withdrawal. These telephones may not be used on party lines or coin operated lines.  
 

CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES  

The telephone company is entitled to make changes in its facilities equipment, operations, and procedures. Should these changes be expected to render your 
terminal equipment incompatible with the telephone company's facilities you will be given sufficient notice to allow you to make the necessary  
modification to your terminal equipment without any interruption of your service.  

SAVE THESE INSTRUCTIONS

 

1.    Never install the telephone wiring during a lightning storm. 
2.    Never install the telephone jacks in wet locations unless the jack is specifically designed for wet locations. 
3.    Never touch un-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 
4.    Use caution when installing or modifying telephone lines. 

NOTIFICATION TO TELEPHONE COMPANY 

IMPORTANT SAFETY INSTRUCTIONS

 

Содержание Marquis EUROMW5
























Отзывы: