Teledyne T101 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 375

Teledyne T101 Скачать руководство пользователя страница 72

Operating Instructions

Teledyne ML – T101 Operation Manual

68

4.4.4.3.

Reporting Range Modes

The T101 provides three analog output range modes to choose from. The actual signals
output on the two analog signal channels depends on whether or not the analyzer includes
a SO

2

/H

2

S multigas measurement option and if so which measurement mode is selected.

•

Single range (SNGL) mode: This mode sets a single maximum range for

the analog output. If single range is selected (see Section 4.4.4.4) both

outputs are slaved together and will represent the same measurement

span (e.g. 0-50 ppm), however their electronic signal levels may be

configured differently (e.g. 0-10 VDC vs. 0-.1 VDC – see Section 4.6.3.1).

In SO

2

/H

2

S multigas measurement mode, although the two inputs are

measuring different gases, the two measurements scales are identical.

Independent range (

IND

) mode: This mode allows the

A1

and

A2

outputs to be

configured with different measurement spans (see Section 4.4.4.5) as well as separate
electronic signal levels (see Section 4.6.3.1) and, if the instrument is equipped with the
SO

2

/H

2

S multigas measurement option, different gas measurements.

•

Auto range (AUTO) mode: As in single range mode, both outputs are

slaved together and will represent the same measurement span; however

this mode gives the analyzer the ability switch to automatically switch

between the two user selected ranges (High and Low). This switching

occurs dynamically as the concentration value fluctuates.

High/low range status is output via the External Digital I/O Status Bits (see Section
5.1.1.1).

To select the Analog Output Range Type press:

SAMPLE RANGE = 500.0 PPB

H2S

=XXX.X

< TST TST > CAL

SETUP

SAMPLE

ENTER SETUP PASS : 818

8 1 8

ENTR

EXIT

SETUP X.X

CFG DAS

RNGE

PASS CLK MORE

EXIT

SETUP X.X

RANGE CONTROL MENU

MODE

SET UNIT

EXIT

SETUP X.X

RANGE MODE:

SNGL

SNGL

IND AUTO

ENTR EXIT

EXIT

Returns

to the Main

SAMPLE

Display

Only one of the

range modes may

be active at any

time.

«
...
70
71
72
73
74
...
»

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов