manualshive.com logo in svg

Teledyne PS200 Series, Руководство по эксплуатации и техническому обслуживанию, Страница: 51 / 58

Поделиться
Скачать
Teledyne PS200 Series Скачать руководство пользователя страница 51

PS200

PORTABLE GAS MONITOR

CALIBRATION

64171, Rev. 11/December 2019

9-3

5. Once gas is applied, press and hold the R button to start the calibration. The 60 second count

-

down will commence (refer to 

Figure 9-4:

 

APPLY GAS Screen

). After 60 seconds, the monitor

will be calibrated to the predefined values.

Figure 9-4: APPLY GAS Screen

6. The timer will count up to 9 seconds, during which time the monitor will adjust the gain to the

sensors accordingly. No manual input is required.

Figure 9-5: APPLY GAS Screen

7. Once calibration is successfully completed, the user has the option of saving the results (see

Figure 9-6:

 

CAL COMPLETE/SAVE RESULTS Screen

).

Figure 9-6: CAL COMPLETE/SAVE RESULTS Screen

8. Using the L button, highlight one of the 3 the available options:

NOTE: The test gas must match the predefined cylinder values stored in the monitor.

Содержание PS200 Series



























































Отзывы:

Нет отзывов