Teledyne Optima Скачать руководство пользователя страница 42

Страница: 42 / 112

Platinum/Optima CVE Refrigerated Sampler

2-24

2.9 Configure and Program the

Sampler

To complete the installation, the sampler

software should be configured and
programmed. Refer to Section 3 for
programming instructions or Section 2.11 for
the quick start guide.

Configure the sampler to make sure that it
recognizes what bottle configuration is
installed. Program the sampler to specify how
and when the sampler should collect liquid
samples.

2.10 Locking the Sampler

Locking the sampler is an optional step that
can prevent tampering with the sampler
operation or collected samples.

To prevent tampering with the sampler

operation, the sampler has a P

ROGRAM

OCK

When enabled, this software feature requires a

numeric password to access most of the control
panel functions. Refer to Section 3.3.9 to enable
this option.

To prevent tampering with the collected

samples, place a padlock on the refrigerator
door latch and control panel.

Содержание Optima

















































































































Результаты поиска

Содержание Optima

Отзывы:

Teledyne Optima, Карманный справочник, Страница: 42 / 112

Результаты поиска

Содержание Optima

Отзывы: