Teledyne Optima Скачать руководство пользователя страница 43

Страница: 43 / 112

Section 2 Installation

2-25

2.11 Quick Start Guide

2.11.1 Program Ready Screen

At initial power up, the controller displays the

ROGRAM

EADY

screen:

To run the displayed program, select F1 for

. Program timer begins and the program

runs as specified.

• Select F1 to S

TOP

the program at any

point of the program running mode.

• Select F1 again to R

ESET

the program

and go back to the P

EADY

screen.

To configure the program settings, select F3 for

ENU

. Use the arrows to the right of the

display to scroll through the programs (1-6).
Press F3, or S

to select the program to

configure.

• Optionally scroll through the P

ROGRAM

ONFIGURATION

ONFIG

) menu

using the arrow keys to select which
program setting to configure. The
following list displays all of the variable
sub-settings within each program
setting.

2.11.2 Program Configuration

Cycle

: Set the sampling parameters here.

Prepurge

: Enter the number of seconds (0-99)

for the system to purge the intake lines prior to
sampling. Then press F3 to accept.

Содержание Optima

















































































































Результаты поиска

Содержание Optima

Отзывы:

Teledyne Optima, Карманный справочник, Страница: 43 / 112

Результаты поиска

Содержание Optima

Отзывы: