manualshive.com logo in svg

Teledyne HVG-2020A, Инструкция по эксплуатации, Страница: 6 / 29

Поделиться
Скачать
Teledyne HVG-2020A Скачать руководство пользователя страница 6

HVG-2020A Instruction Manual

 

Page 6 of 29 

 

Features 

COLOR DISPLAY WITH TOUCH PANEL.  The HVG-2020A has an optional integrated touch panel color LCD 

display. This gives the user easy configurability, stand-alone operation and local control over the instrument. 
SUPERIOR ACCURACY.  The output of the piezo-resistive sensor is thermally compensated and linearized to 

provide accuracy of ± (0.1% of r 0.5 Torr), and better than ± (0.6% of r 0.5 Torr) over the 

entire operating temperature range after zero adjustment.  
GAS INDEPENDENT.  The piezo-resistive sensor is media isolated and provides a direct pressure measurement 

that is gas species independent.  
300 SERIES STAINLESS STEEL.  The vacuum envelope of the HVG-2020A is entirely 300 series stainless steel 

with welded construction.  Using metal seal vacuum connections eliminates the permeation, degradation and 

outgassing problems of elastomer O-rings. 
FLEXIBLE POWER REQUIREMENTS.  The HVG-2020A can operate with any power supply capable of providing 12 

– 36 VDC via the 9-pin D connector or a 2 mm bayonet jack connection. 
DIGITAL COMMUNICATIONS.  The HVG-2020A is equipped with RS232/RS485 and USB for digital 

communications. The USB connector serves as a virtual COM port for serial communication, eliminating the 

need for a USB to Serial converter. 
ANALOG OUTPUTS.  The pressure is available as a linear voltage or current analog signal. The 0-20 mA or 4-20 

mA current option gives the user the advantages of a current loop output to minimize environmental noise 

pickup and signal loss over long cable runs. 
TTL ALARMS.  Two alarm signals are provided with an open-drain configuration, one to indicate when pressure 

goes above a value and the other below a value. 
LED INDICATORS.  Two LEDs provide instrument status and system pressure information. 
 

 

Содержание HVG-2020A






























Отзывы:

Нет отзывов