Teledyne HDO9000 Скачать руководство пользователя страница 24

Страница: 24 / 188

HDO9000 High Definition Oscilloscopes Operator's Manual

Auxilliary Output

To output signal from the instrument to another device, connect a BNC cable from Aux Out to the

other device. Go to Utilities > Utilities Setup > Aux Output to

configure the output

Language Selection

To change the language that appears on the touch screen:

1. Go to

Utilities > Preference Setup > Preferences

and make a

Language

selection.

2. Follow the prompt to restart the application.

To also change the language of the Windows operating system dialogs:

1. Choose File > Minimize to hide X-Stream and show the Windows Desktop.

2. From the Windows task bar, choose

Start > Control Panel > Clock, Language and Region

3. Under Region and Language select

Change Display Language

4. Touch the

Install/Uninstall Languages

button.

5. Select

Install Language

and

Browse Computer or Network

6. Touch the

Browse

button, navigate to D:\Lang Packs\ and select the language you want to

install. The available languages are: German, Spanish, French, Italian, and Japanese. Follow

the installer prompts.

Reboot

after changing the language.

Note:

Other language packs are available from Microsoft’s website.

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды