Teledyne HDO9000 Скачать руководство пользователя страница 164

Страница: 164 / 188

HDO9000 High Definition Oscilloscopes Operator's Manual

Auxiliary Output

Use the Aux Output dialog to configure the output of the

Aux Out

port.

Auxiliary Output

Trigger Enabled

sends a pulse when the trigger is ready (Ready indicator lit), but not necessarily

triggered. It can be used as a gating function to trigger another instrument. Enter the desired pulse

Amplitude

Trigger Out

sends a pulse upon a trigger (TRIG'D Indicator lit). Enter the desired pulse

Amplitude

Pass/Fail

generates a pulse when Pass/Fail testing is active and conditions are met. Enter the

desired

Pulse Duration

Fast Edge

provides a fast edge signal that can be used to deskew multiple channels.

Off

disables auxiliary input/output.

Calibration Output

Choose the signal to be output from the Cal Out hook on the front of the instrument:

Square

wave signal. Enter the wave

Frequency

and

Amplitude into 1 MΩ

, or choose to

Set to 1

kHz, 1 V Square Wave

Reference

DC Level

. Enter an

Amplitude into 1 MΩ

Off

disables calibration output.

154

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды