Teledyne ADFM Hot Tap Скачать руководство пользователя страница 92

Страница: 92 / 116

ADFM® Flow Meter
Section 3 Maintenance and Troubleshooting

3-6

3.4 Troubleshooting the

ADFM

The following sections provide assistance in locating and iso-
lating faults in the system.

3.4.1 Troubleshooting

Tables

Troubleshooting information for system power-up is provided in
Table 3-1, and for system operation in Table 3-2. Possible
problems and actions are listed in order of likelihood.

Note

Call the factory for assistance before replacing the mother-
board.

Table 3-1 Troubleshooting on Power-Up

Symptom

Possible Problem(s)

Action(s)

No wakeup message on LCD or com-
puter screen

Power

Motherboard

Verify battery voltage and connec-
tions. Verify connection to external
DC supply.

Contact the factory.

No wakeup message on LCD, but com-
puter displays wakeup message when a
manual reset is performed.

LCD

Front panel interface board

Cable connection between LCD and
front panel

Cable connection between front
panel interface board and mother-
board.

Motherboard

Replace LCD

Replace front panel interface board

Replace ADFM Motherboard.

No wakeup message on computer
screen, but LCD displays wakeup mes-
sage and completes Built-In-Tests (BIT).

RS-232 connection

Incorrect port settings on computer

Front panel interface board

Motherboard

Troubleshoot cabling

Adjust communication port settings
on computer

Replace front panel interface board

Replace motherboard.

Содержание ADFM Hot Tap





















































































































Результаты поиска

Содержание ADFM Hot Tap

Отзывы:

Teledyne ADFM Hot Tap, Инструкция по установке и эксплуатации, Страница: 92 / 116

Результаты поиска

Содержание ADFM Hot Tap

Отзывы: