Teledyne ADFM Hot Tap Скачать руководство пользователя страница 58

Страница: 58 / 116

ADFM® Flow Meter



Section 2 Setup and Installation

2-38

3. Break off any excess length from the threaded couplers

(Figure 2-41) such that the remaining threads attach the
sensor snugly into the fairing.

Figure 2-41 Threaded couplers: break off at joint

2.6.8 Pro20 Sensor

Mounting Hardware

Table 2-1 List of Pro20 Sensor Mounting Accessories

Cable mounting kit - Pro20 sensor only

60-7709-003

Cable mounting kit - Pro20 & pressure sensor

60-7709-002

Single SST Loop - Pro20 sensor only

489-0016-23

Single SST Loop - Pro20 & pressure sensor

489-0016-25

Scissors Ring standard sensor mounting hardware kit

60-3004-178

Scissors Ring secondary sensor mounting hardware kit

60-7709-001

Sensor mounting plate

60-7613-003

Sensor mounting screws

231-8116-10

Debris fairing

60-7004-042

Spacer, 1 inch lift

60-7004-043

Spacer, 2 inch lift

60-7004-044

Spacer, 4 inch lift

60-7004-045

Threaded coupler

60-7614-001

Replacement hardware kit for fairing/spacer

60-7619-001

Содержание ADFM Hot Tap





















































































































Результаты поиска

Содержание ADFM Hot Tap

Отзывы:

Teledyne ADFM Hot Tap, Инструкция по установке и эксплуатации, Страница: 58 / 116

Результаты поиска

Содержание ADFM Hot Tap

Отзывы: