Teledyne 9070 Скачать руководство пользователя страница 34

Страница: 34 / 50

1. Linear oxygen (0.1 to 100.0%)

2. Low range linear oxygen (10 to 10,000 ppm)
The output spans are adjustable in Set-up steps 21 and 22.

21. TRANSMITTER ZERO CHANNEL 1

Select transmitter zero for output Channel 1.
Range 0.0 to 99.9% Oxygen.
Range 0 to 0.999% (9,990ppm) Oxygen.
Default setting is 0.0%.

22. TRANSMITTER SPAN CHANNEL

Select transmitter span for output Channel 1.
Linear Oxygen-

Range 0.1 to 100.0% Oxygen. Default setting is 10.0%.

Low Oxygen-

Range 0.001 to 1.000% (10 to 10,000ppm) Oxygen. Default setting is 0.100%.

23. TRANSMITTER OUTPUT CHANNEL 2

Select the type of output required for Channel 2.

Options:

1.  Sample Gas, oxygen
2.  Linear (Low) Oxygen, 0.1 to 100.0 % *
3.  Logarithmic oxygen, 0.1 to 20 %
4.  % carbon dioxide
5.  Reducing oxygen %
6.  Oxygen sensor EMF

24. TRANSMITTER ZERO CHANNEL 2

The output zero and span of Channel 2 is set in set-up steps 24 and 25. Range limits are shown below.

25. TRANSMITTER SPAN CHANNEL 2

Output

Zero Range

Span Range

Minium span

SAMPLE GAS, OXYGEN

0.0 to 99.9 %

0.1 to 100 %

0.1 %

LOW OXYGEN

0.0 to 99.9 %

0.1 to 100 %

0.1 %

LOG OXYGEN

0.1 % oxygen fixed

20 % oxygen fixed

(see Note 1)

CARBON DIOXIDE

0 to 80 %

20 to 100.0 %

20 %

REDUCING OXYGEN

to 10

-28

to 10

% Two

decades

(see Note 2)

oxygen in one

decade steps

decade steps.

SENSOR EMF

0 to 1100 mV in

100 to 1300 mV

100 mV

100 mV steps

in 100 mV steps

NOTE

For log oxygen scale details, Refer to Appendix 2.

Note that the reducing oxygen span is shown on the display as the exponent only. -1 represents 10

-1

% oxygen.

26. SAMPLE MODE

Options

1. Fast Sample
2. Display Sample

3. Continuous

Page

Teledyne Analytical Instruments 9070 Oxygen Analyzer

Содержание 9070



















































Результаты поиска

Содержание 9070

Отзывы:

Teledyne 9070, Инструкция по эксплуатации, Страница: 34 / 50

Результаты поиска

Содержание 9070

Отзывы: