manualshive.com logo in svg

Teledyne 460H NEMA, Инструкция по эксплуатации

Поделиться
Скачать
Teledyne 460H NEMA Скачать руководство пользователя страница 8

1.2 WARRANTY POLICY 

ADVANCED POLLUTION INSTRUMENTATION DIVISION 

02024c 

 

Prior to shipment, Teledyne API equipment is thoroughly inspected and tested.  Should equipment 
failure occur, Teledyne API assures its customers that prompt service and support will be available. 

COVERAGE 

After the warranty period and throughout the equipment lifetime, Teledyne API stands ready to 
provide on-site or in-plant service at reasonable rates similar to those of other manufacturers in the 
industry.  All maintenance and the first level of field troubleshooting are to be performed by the 
customer. 

NON-

 

TELEDYNE API MANUFACTURED EQUIPMENT 

Equipment provided but not manufactured by Teledyne API is warranted and will be repaired to the 
extent and according to the current terms and conditions of the respective equipment manufacturers 
warranty.  

GENERAL 

Teledyne API warrants each Product manufactured by Teledyne API to be free from defects in 
material and workmanship under normal use and service for a period of one year from the date of 
delivery. All replacement parts and repairs are warranted for 90 days after the purchase. 
 
If a Product fails to conform to its specifications within the warranty period, Teledyne API shall 
correct such defect by, in Teledyne API's discretion, repairing or replacing such defective Product or 
refunding the purchase price of such Product. 
 
The warranties set forth in this section shall be of no force or effect with respect to any Product: 
(i) that has been altered or subjected to misuse, negligence or accident, or (ii) that has been used in 
any manner other than in accordance with the instruction provided by Teledyne API or (iii) not 
properly maintained. 
 

THE WARRANTIES SET FORTH IN THIS SECTION AND THE REMEDIES 
THEREFORE ARE EXCLUSIVE AND IN LIEU OF ANY IMPLIED WARRANTIES 
OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE OR OTHER 
WARRANTY OF QUALITY, WHETHER EXPRESSED OR IMPLIED.  THE 
REMEDIES SET FORTH IN THIS SECTION ARE THE EXCLUSIVE REMEDIES 
FOR BREACH OF ANY WARRANTY CONTAINED HEREIN.  

TELEDYNE

 API 

SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL 
DAMAGES ARISING OUT OF OR RELATED TO THIS AGREEMENT OF 

TELEDYNE

 API'S PERFORMANCE HEREUNDER, WHETHER FOR BREACH OF 

WARRANTY OR OTHERWISE. 

 
TERMS AND CONDITIONS 

All units or components returned to API should be properly packed for handling and 
returned freight prepaid to the nearest designated Service Center.  After the repair, the 
equipment will be returned, freight prepaid. 

P/N 03662D Teledyne API Model 460H O3 Monitor Operator Manual - Page 8 

Содержание 460H NEMA







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды