Teledyne 2240 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 13

Teledyne 2240 Скачать руководство пользователя страница 5

Page 9 of 26

M2240

R0

2.

2240

Functions and Features

General Features

The

2240

is designed as three section unit housed in a

tough ABS carrying case with all the necessary
accessories. The principle sections are:

•

Controller – Containing the user interface, battery, and
external electrical interfaces. (Serial and analog).

•

Wand Assembly – extends the operator’s reach by 24
inches,

making operation highly flexible.

•

Sensor Module – Containing the sensor element and
sensor-specific electronics. Easily mounted on either the
Controller or Wand Assembly.

Electrical Features

•

Power provided by either the internal battery or through an
optional

Teledyne

external power supply.

•

Automatic self-test, activated on start-up, to confirm
proper operation.

•

Serial Interface: 9 pin Sub-D connector in RS-232
configuration transmitting ASCII data in an 8 bit stream
with no parity and 1 stop bit.

•

Analog Interface: 0-5 V and 4-20 mA. (Reference Figure
3). The analog output produces a signal proportional to the
amount of hydrogen in air, an indication of Warm-Up
Mode, or an indication of Error Mode as determined by the
operator-selected format. (See section 5)

Operator Interface Features

•

LCD: provides readable (alphanumeric) information on
current readings and settings..

•

Tri-colored (green/yellow/red) LED: indicates instrument
status and changes in hydrogen concentration.

•

Audible alarm: Operator programmable level provides a
single beep each time a new peak hydrogen concentration
is detected and provides a continuous series of beeps if the
programmable Alarm setting is exceeded.

Page 10 of 26

M2240

R0

3.

Component

Identification

Connector

Handle

Sensor Module

containing the Wide

Range Sensor®

LED Display

Mode

Button

LCD Display

Enter Button

Power Button

Scroll

Buttons

LED Display

Controller

Receiver

Sensor

Module,

shown

attached after

removing

from the

Controller

Battery Door

Release Tab

Sensor

Release Tab

Battery Door

Wand

Assembly

Coiled Cable

Figure 2 -

2240

Controller and Wand Assy.

«
...
3
4
5
6
7
...
»

Содержание 2240














Отзывы:

Нет отзывов