manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 82 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 82

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Table 6-1:  Zero/Span Valve Operation 

Mode 

Description 

Reference Section 

1. 

Front panel operation via 
CALS and CALZ buttons 

Calibration Section 7 - Manual Zero/Span Check. 

2. 

Automatic operation using 
AUTOCAL 

Setup and use of AUTOCAL is described in Table 6-2, 
and Section 7.4. 

3. 

Remote operation using the 
RS-232 interface 

Setup described in Table 6-2. Operation of AUTOCAL 
described in Section 5.5 and Section 7 - Calibration. A 
complete description of the RS-232 interface is available. 
Order part number 01530. 

4. 

Remote operation using 
external contact closures 

Section 7.7 - Automatic operation using external contact 
closures. Truth Table 7-9 and Section 9.3.4.3. 

 

The Zero/Span valves have 3 operational states: 

1.

 

Sample mode. Here both valves are de-energized and sample gas passes through the 

sample/cal valve and into the analyzer. 

2.

 

Zero mode. The sample/cal valve is energized to the cal mode. The zero/span valve is de-

energized in the zero mode, thus allowing zero gas to be admitted through the rear panel 
bulkhead fitting into the analyzer. 

3.

 

Span mode. The sample/cal valve is energized and in the cal mode. The zero/span valve 

is energized in the span mode. With both valves on, span gas is admitted through a rear panel 
bulkhead fitting into the analyzer. 

Zero air and span gas inlets should supply their respective gases in excess of the 500 cc/min 
demand of the Analyzer. Supply and vent lines should be of sufficient length and diameter to 
prevent back diffusion and pressure effects. See Figure 2-3 for fitting location and tubing 
recommendations. 

Adequate zero air can be supplied by connecting a Purafil/charcoal scrubber and 5 micron 
particulate filter (Teledyne API P/N 000369) to the zero air inlet tubing. The zero air scrubber 
used in conjunction with the Zero/Span Valve option provides an inexpensive source of zero air. 
Another source of zero air is the Model 701 zero air generator. 

6-2 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов