Teledyne 200A Скачать руководство пользователя страница 195 | Manualshive

Страница: 195 / 220

Teledyne 200A Скачать руководство пользователя страница 195

Teledyne API Model 200A NO

X

Analyzer Instruction Manual, 02246, Rev. F1

PSM Diagnostic Procedures

The Linear Power Supply board can be tested by checking the DCPS - TEST function on the
front panel. It should read 2500 mV ± 200 mV. If the value is outside this range, individual
output voltages can be tested on connector P3, see Schematic in the Appendix for pinouts.

The Switching Power Supply output can be tested by observing the temperature of the PMT cold
block using the PMT TEMP - TEST function. The temperature should be constant 7± 2

°

C. The

output voltage can be observed on J10 of the Switch Board. It should be 15 VDC ± 0.5.

The Switch Board can be tested by observing the diagnostic LEDS along the top edge of the
board. The following Table 9-10 describes the typical operation of each LED.

Table 9-10: Power Supply Module LED Operation

No.

Function

Description

1. NO/NO

x

Valve

Should switch about every 5 sec.
On(click sound) = NO

x

mode

Off(thud sound) = NO mode

2.

Zero/Span Valve

Should switch ON when CALZ or CALS button is
pressed.

3.

Sample/Cal Valve

Should switch ON when CALS button is pressed.

4.

AutoZero Valve

ON when M200A in AutoZero mode. Happens once
every 6 NO/NO

x

cycles or about once per minute.

5.

Ozone Generator Power

The ozone generator will be on if it has been more than 30
min since power up.

6.

Sample flow control block
heater

Should cycle ON-OFF every 20 sec to 2 min. On
continuously until up to temp.

7.

Converter Heater

Should cycle ON-OFF every 20 sec to 2 min. On
continuously until up to temp.

8.

Reaction Cell Heater

Should cycle ON-OFF every 20 sec to 2 min. On
continuously until up to temp.

9-53

«
...
193
194
195
196
197
...
»

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов