manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 148 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 148

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Table 9-1:  Test Functions (Continued) 

Test Function 

Factory Set-Up 

Comment 

AZERO 

Check value in 
Final Test Values 
Table 2-1 

AZERO is the current value of the AutoZero circuit reading. 
Values are typically 0 mV -20/+150. For values outside this range, 
check the AutoZero and NO/NO

x

 valve for cross port leaks. Use 

Diagnostic mode to manually check the AutoZero valve for 
correct operation.  

HVPS 

450-900 VDC 

This represents the scaled-up HVPS programming voltage to the 
HVPS. The design of the HVPS precludes taking a single reading 
that indicates the health of the supply. Refer to the HVPS 
Troubleshooting Section 9.3.8.5 for a procedure for testing the 
HVPS. This TEST function is used primarily to set the HVPS 
voltage value. A value not in the 450 to 900 volt range indicates 
problems with the HVPS supply. 

DCPS 

2500 

±

 200 mV 

DCPS is a composite of the +5 and 

±

 15 VDC supplies. It has 

been arbitrarily set at 2500 

±

 200 mV. If it is not in this range one 

of the voltages in the supply is not working. Check the procedures 
for diagnosing the Power Supply Module in Section 9.3.5. 

RCELL TEMP 

50 

±

 1

°

 C 

The reaction cell temperature is controlled to 50

°

 C 

±

 1

°

 C by the 

computer. It should only read other values when the instrument is 
warming up. If the value is outside the acceptable range, go to the 
procedure for diagnosing the Reaction cell temp supply in Section 
9.3.8.2. The alarm limits are less than 45

°

 C and greater than  

55

°

 C.  

BOX TEMP 

8-48

°

 C 

The Box Temp is read from a thermistor on the Status/Temp board 
(01086). It should usually read about 5

°

 C above room temp. The 

M200A is designed to operate from 5 to 40

°

 C ambient. Therefore 

the box temperature should be in the range of about 10 to 50

°

 C. 

Temperatures outside this range will cause premature failures of 
components, and poor data quality. Warning limits are < 8

°

 C and 

> 48

°

 C. 

PMT TEMP 

7 

±

 1

°

 C 

The PMT detector is very temperature sensitive.  The PMT 
temperature should always be 7

°

 C, except at power-up. 

Temperatures more than 

±

1

°

 C from the set point indicate 

problems with the cooler circuit. See Section 9.3.8.4 for PMT 
cooler diagnostic and troubleshooting. Warning limits are < 5

°

 C 

and > 15

°

 C. 

MOLY TEMP 

315 

±

 5

°

 C 

Moly temp is controlled by the CPU to 315

°

 C. After cold start it 

requires about 30 min to come to temperature. After temperature is 
reached temperature should not vary more than 

±

 5

°

 C. See 

Section 9.3.4 for troubleshooting. Warning limits are < 290

°

 C and 

> 320

°

 C. 

(table continued) 

9-6 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов