manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 204 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 204

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

9.3.8

x

 Sensor Module 

Figure 9-9 and Figure 9-10 show the assembly of the NO

x

 sensor module. 

9.3.8.1  PMT 

The PMT detects the light emitted by the reaction of NO with ozone. It has a gain of about 
500,000 to 1,000,000. It is not possible to test the detector outside of the instrument in the field. 
The best way to determine if the PMT is working is by using Optic Test. OT operation is 
described in Section 9.1.3.3.  

The basic method to diagnose a PMT fault is to eliminate the other components using ET, OT 
and specific tests for other sub-assemblies. 

9.3.8.2  Reaction Cell Temp 

The reaction cell temperature is controlled by the CPU. It operates by reading a thermistor 
amplifier on the 01086 Status/Temp board. The CPU controls the temperature by toggling a bit 
on the V/F board. The V/F board TTL logic controls a solid state switch on the Switch Board in 
the PSM. The switched 115VAC comes out of the PSM to a connector near the underside of the 
reaction cell. A warning message may be present during initial warm-up or if the connector is 
not plugged in after cleaning the reaction cell. 

9.3.8.3  Preamp Board 

The NO

x

 Preamp Board is a multifunction board providing circuitry to support the following 

functions. 

1.

 

Preamp, buffer amplifier, physical range control hardware for the PMT detector. 

2.

 

Precision voltage reference and voltage generation, and control for the PMT - HVPS 

inside the sensor module. 

3.

 

Constant current generator and adjustment for the Optic Test LED. 

4.

 

Voltage generation and adjustment for Electric Test. 

5.

 

Thermistor amplifier, control signal generation for the PMT cooler. 

The setup and adjustment of items 1-4 above is covered in the Factory Calibration procedure in 
Section 9.1.6. Item 5 has no adjustable features. 

  

NO

9-62 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов