Teledyne Lecroy Frontline BPA 600 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 348

Teledyne Lecroy Frontline BPA 600 Скачать руководство пользователя страница 12

2.1.1.1 Status LED

The Frontline BPA 600 has two Status LEDs on the RF panel. In the front panel center are the

LOW ENERGY

and

BR/EDR

LEDs.

Figure 2.3 - BPA 600 Hardware LEDs

LED Color

Frontline BPA 600 Activity

LED Off

Frontline BPA 600 device is idle.

Green

Frontline BPA 600 is actively sniffing waiting for configured devices to connect.

Blue

The configured devices have connected (Asynchronous Connectionless Link (ACL)).

Intermittent
Blue

Configured devices are in "Sniff mode" (slave is listening at a reduced rate, conserving
device power).

Table 2.1 - Frontline BPA 600 LED Status

2.1.2 Connecting/Powering the Frontline BPA 600 Hardware

Once you have attached the antennas, the next step is to power up and connect the Frontline BPA 600
hardware to the computer.

1. Insert the USB cable into the USB port on the Frontline BPA 600 hardware. The Frontline BPA 600

analyzer requires no external power (Figure 2.4).

Figure 2.4 - BPA 600 USB Connector

2. Insert the other end of the USB cable into the PC.

The next thing to do is to turn on the devices that you will be testing.

2.1.3 BPA 600 ProbeSync

Any Frontline hardware with ProbeSync™ can be connected together to run off of a common clock, ensuring
precise timestamp synchronization.

Simply plug the supplied Cat 5 cable into the

OUT

connector on the sniffer that will be supplying the clock

and connect the other end to the

IN

connector on the sniffer receiving the clock. (

). If using a

BPA 600 analyzer with a different Frontline analyzer, the BPA 600 analyzer must provide the clock. Combined
cable length of all the ProbeSync cables connected at a given time should not exceed 1.5 meters (4.5 feet).

TELEDYNE LECROY

Chapter 2 Getting Started

4

Frontline BPA 600 Hardware & Software User Manual

«
...
10
11
12
13
14
...
»

Содержание Frontline BPA 600





























































































































































































































































































































































Отзывы:

Нет отзывов