manualshive.com logo in svg

TELEDYNE API T300, Руководство по эксплуатации

Поделиться
Скачать
TELEDYNE API T300 Скачать руководство пользователя страница 206

Calibration Procedures 

Teledyne API – Model T300/T300M CO Analyzer 

204 

9.3.3.3. 

USE OF ZERO/SPAN VALVE WITH REMOTE CONTACT CLOSURE 

Contact closures for controlling calibration and calibration checks are located on the rear 
panel 

CONTROL IN

 connector.  Instructions for setup and use of these contacts can be 

found in Section 3.3.1.6. 

When the appropriate contacts are closed for at least 5 seconds, the instrument switches 
into zero, or span  calibration mode and any internal zero/span valves installed will be 
automatically switched to the appropriate configuration.   

•

 

The remote calibration contact closures may be activated in any order.   

•

 

It is recommended that contact closures remain closed for at least 10 minutes to 
establish a reliable reading. 

•

 

The instrument will stay in the selected mode for as long as the contacts remain 
closed. 

If contact closures are being used in conjunction with the analyzer’s AutoCal  (see 
Section  9.4) feature and the AutoCal attribute “

CALIBRATE”

  is  enabled, the 

T300/T300M will not recalibrate the analyzer until the contact is opened.  At this point, 
the new calibration values will be recorded before the instrument returns to 

Sample 

Mode

.   

If the AutoCal  attribute “

CALIBRATE”

  is  disabled,  the instrument will return to 

Sample Mode

, leaving the instrument’s internal calibration variables unchanged. 

9.4.

 AUTOMATIC ZERO/SPAN CAL/CHECK (AUTOCAL) 

The AutoCal  system allows unattended periodic operation of the Z

ERO/SPAN

  valve 

options by using the T300/T300M  Analyzer’s internal time of day clock.  AutoCal 
operates by executing 

SEQUENCES

  programmed by the user to initiate the various 

calibration modes of the analyzer and open and close valves appropriately.  It is possible 
to program and run up to three separate sequences (

SEQ1

, 

SEQ2

  and 

SEQ3

).  Each 

sequence can operate in one of three modes, or be disabled. 

Table 9-2: 

AUTOCAL Modes 

MODE NAME 

ACTION 

DISABLED 

Disables the Sequence. 

ZERO 

Causes the Sequence to perform a Zero calibration/check. 

ZERO-SPAN 

Causes the Sequence to perform a Zero point calibration/check followed by a 
Span point calibration/check. 

SPAN 

Causes the Sequence to perform a Span concentration calibration/check only. 

06864D DCN7562

Содержание T300




























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды