3)
To end the call, press the “SPEAKERPHONE” key again. The “SPEAKERPHONE”
LED will turn off.
T
O
M
AKE A
C
ALL
U
SING THE
H
ANDSET
, W
HILE
D
IALING
W
ITH THE
B
ASE
K
EYPAD
1)
Pick up the handset and press the desired “LINE” key. The LED will illuminate.
2)
Listen for dial tone, then dial the desired number using base keypad.
3)
To end the call, place the handset on the base cradle or press the “LINE” on/off key
for the active line.
U
SING THE
H
OTEL
S
ERVICES
D
IRECT
A
CCESS
(A
UTO
D
IAL
) K
EYS
Using the speakerphone:
1)
Press “SPEAKERPHONE” key. The “SPEAKERPHONE” LED will illuminate.
2)
Listen for dial tone, then dial the desired number by pressing the hotel services direct
access key where the number was stored.
3)
To end the call, press “SPEAKERPHONE” key again. The “SPEAKERPHONE”
LED will go out.
Using the handset
:
1)
Pick up the handset and press a “LINE” key. The LED will illuminate.
2)
Listen for a dial tone, then dial the desired number by pressing the hotel services
direct access key on the base where the number was stored.
3)
To end the call, press the handset “LINE” key for the active line. The LED will go out.
C
ONFERENCE
C
ALLS
The “CONFERENCE” key allows the user to include two other parties in a three-way
phone conversation. Typical conference calls would be:
a) User initiates two calls
b) User initiates one call after receiving a call
c) User includes two callers
User initiates two calls:
1)
Place call to first party.
2)
Place the first party on hold by pressing the “HOLD” key.
3)
Place call to second party using the available, unused line.
4)
Press the “CONFERENCE” key. The parties will be connected.
User initiates one call:
1)
Receive call from first party.
2)
Place caller on hold by pressing the “HOLD” key.
3)
Place call to second party using the available, unused line.
4)
Press the “CONFERENCE” key. The parties will be connected.
User includes two callers:
1)
Receive call from first party and place it on hold.
2)
Receive call from second party.
3)
Press the “CONFERENCE” key. The parties will be connected.
T
ERMINATING A
C
ONFERENCE
C
ALL
Pressing either “LINE” key will maintain the connection with the selected line while
dropping the other. Pressing the “CONFERENCE” or “SPEAKERPHONE” key will
disconnect both lines.
L
AST
N
UMBER
R
EDIAL ON
B
ASE
1)
Press the “SPEAKERPHONE” key. The “SPEAKERPHONE” LED will illuminate.
2)
Press the “REDIAL” key, and the telephone will dial the last number dialed.
3)
To end the call, press “SPEAKERPHONE” again. The “SPEAKERPHONE” LED
will turn off.
L
AST
N
UMBER
R
EDIAL ON THE
H
ANDSET
1)
Pick up the handset and press the a “LINE” key. The LED will illuminate.
2)
Press the “REDIAL” key, and the telephone will dial the last number dialed.
3)
To end the call, press the “LINE” key again. The LED will turn off.
F
LASH ON
B
ASE AND
H
ANDSET
The “FLASH” key is dedicated to perform a timed hookflash.
Note:
There are three flash programming keys (recessed) to select different flash times
(100/300/600 ms.) See diagram inside front cover for more information.
T
O
M
UTE THE
S
PEAKERPHONE
1)
Press the “MUTE” key on base. The “MUTE” LED will illuminate, to indicate that
mute is active.
2)
Press the “MUTE” key again to disable mute. The “MUTE” LED will turn off.
P
AUSE
Pause can be entered during off-hook manual dialing and chain dialing. This is a means of
allowing a complex number to be redialed. Pause has been inserted for the handset and the
base. Pause can be stored into the memory of hotel services direct access keys.
P
AGING
This key initiates a handset page. When paging is active, the handset will beep. The mes-
sage LED and the “ON” LED key on the handset will flash. To page:
1)
Press “PAGE” key on the base. The handset will beep.
2)
The handset will stop beeping if answered, by pressing “ON” or “OFF” key on the
handset, or by pressing the “PAGE” key on the base again.
Note:
The handset will not beep if the handset is in use. If the page is stopped by pressing
the “ON” or “OFF” key within 30 seconds of receipt of the page from the base, the hand-
set cannot receive another page immediately.
M
ESSAGE
W
AITING
C
ONFIGURATION
When a voice message waiting signal is received, the message-waiting LEDs on both the
handset and base will blink. Both LEDs will turn off once the message has been retrieved.
To configure message waiting mode for
Siemens system
:
1)
Press and hold “Line 1” key on base. Plug in the power supply socket; you will hear
two beeps.
2)
Release “Line 1” key; when you hear two beeps, the set is in Siemens MW mode.
To configure message waiting mode for
non-Siemens systems
:
1)
Press and hold “Line 2” key on base. Plug in the power supply socket; you will hear
two beeps.
2)
Release “Line 2” key; when you hear two beeps, the set is in non-Siemens MW mode.
4
5
