Using the Hold Key
The HOLD key places the call on hold locally at the cordless
telephone.
To Place a Call on Hold:
1. With a call active, press the red HOLD key on either the
handset or base unit.
2. The red line LED will slowly blink, indicating the call is
on hold.
3. If a conference call is active, pressing HOLD will place all
connections on hold.
To Remove a Call From Hold:
1. Press the line key of the call on hold, or the HOLD key
again. This will remove the call from hold, making the call
active again.
2. The red line LED will return to steady illumination,
indicating the line is active.
3. During a conference call, to remove both lines from hold,
press the CONF key.
To Change Phones After Placing a Call on Hold:
1. Place the call on hold as above.
2. Pick up the call at another telephone that is on the same
line. The telephone will activate the line and remove the
hold at the original telephone.
To Mute the Speakerphone
1. Press the MUTE key on the base unit. The red LED above
the MUTE key will illuminate. The party on the other end
will not be able to hear you when the MUTE LED is lit.
2. Press the MUTE key again to turn off the mute feature.
The MUTE LED will go out.
Converting From Desk to Wall Mount
The AC8200/AC9200 series can be adapted for wall mounting
applications. The conversion is easiest to make when the
handset and cords are not connected.
1. Located on the handset cradle, above the speaker grill,
is the wall/desk mount clip. Remove this clip by firmly
pushing it upward towards the top of the phone.
2. Flip the clip over (top to bottom) so that the protruding
edge is towards the top of the phone and replace it in
its slot.This edge will hold the handset when the phone
is mounted on the wall.
3. Turn the telephone over so the bottom is up, facing you.
Place it on a non-abrasive surface to prevent scratching.
4. Locate and remove the mounting bracket. Firmly push back
and pull up to remove two of the four retaining tabs.
5. Rotate the mounting bracket 180º degrees clockwise, so
that the mounting eyelet on the bracket is facing in the
same direction as the other mounting eyelet located on the
bottom of the telephone.
6. Insert the top two retaining tabs of the mounting brackets
into the mounting bracket slots (located near the middle
of the telephone). Then firmly push down to insert
the retaining tabs on the opposite side of the
mounting bracket.
7. Connect a 15-foot RJ-45 cord into the LINE jack on the back
of the phone.
8. Turn the telephone over, and slide the telephone down
onto the mounting posts of the wall bracket. Ensure
that both eyelets line up with the mounting posts.
The Ringer Equivalence Number (REN) of this device is 0.7B.
Notice: The Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the Ringer
Equivalence Numbers of all the devices does not exceed 5. This
telephone connects to the telephone network under the connecting
arrangement code CA11A.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS,
INCLUDING THE FOLLOWING:
1. READ AND UNDERSTAND ALL INSTRUCTIONS.
2. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED
ON THE PRODUCT.
3. UNPLUG THE PRODUCT FROM THE WALL OUTLET BEFORE
CLEANING. DO NOT USE LIQUID CLEANER OR AEROSOL CLEANERS.
USE A DAMP CLOTH FOR CLEANING.
4. DO NOT USE THIS PRODUCT NEAR WATER, FOR EXAMPLE, NEAR
A BATHTUB, WASH BOWL, KITCHEN SINK OR LAUNDRY TUB, IN A
WET BASEMENT, OR NEAR A SWIMMING POOL.
5. DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND OR
TABLE. THE PRODUCT MAY FALL, CAUSING SERIOUS DAMAGE TO
THE PRODUCT.
6. SLOTS AND OPENINGS IN THE CABINET AND THE BACK OF
BOTTOM ARE PROVIDED FOR VENTILATION, TO PROTECT IT FROM
OVERHEATING. THESE OPENINGS MUST NOT BE BLOCKED OR
COVERED. THE OPENINGS SHOULD NEVER BE BLOCKED BY
PLACING THE PRODUCT ON THE BED, SOFA, RUG OR ANY OTHER
SIMILAR SURFACE. THIS PRODUCT SHOULD NEVER BE PLACED
NEAR OR OVER A RADIATOR OR HEAT REGISTER. THIS PRODUCT
SHOULD NOT BE PLACED IN A BUILT-IN INSTALLATION UNLESS
PROPER VENTILATION IS PROVIDED.
7. NEVER PUSH OBJECTS OF ANY KIND INTO THIS PRODUC
THROUGH CABINET SLOTS AS THEY MAY TOUCH DANGEROUS
VOLTAGE POINTS OR SHORT OUT PARTS THAT COULD RESULT
IN A RISK OF FIRE OR ELECTRIC SHOCK. NEVER SPILL LIQUID OF
ANY KIND ON THE PRODUCT.
8. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT DISASSEMBLE
THIS PRODUCT. BUT TAKE IT TO A QUALIFIED SERVICE FACILITY IF
SERVICE OR REPAIR WORK IS REQUIRED. OPENING OR REMOVING
COVERS MAY EXPOSE YOU TO DANGEROUS VOLTAGES OR OTHER
RISKS. INCORRECT REASSEMBLY CAN CAUSE ELECTRIC SHOCK
WHEN THE APPLIANCE IS SUBSEQUENTLY USED.
9. UNPLUG THIS PRODUCT FROM THE WALL OUTLET AND REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL UNDER THE
FOLLOWING CONDITIONS:
- WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED
OR FRAYED.
- IF LIQUID HAS BEEN SPILLED INTO THE PRODUCT.
- IF THE PRODUCT HAS BEEN EXPOSED TO RAIN OR WATER.
- IF THE PRODUCT DOES NOT OPERATE NORMALLY BY
FOLLOWING THE OPERATING INSTRUCTIONS. ADJUST ONLY
THOSE CONTROLS THAT ARE COVERED BY THE OPERATING
INSTRUCTIONS, AS IMPROPER ADJUSTMENT OF OTHER
CONTROLS MAY RESULT IN DAMAGE,AND MAY REQUIRE
