Tektronix TSG4102A Скачать руководство пользователя страница 41

Страница: 41 / 99

Operating basics

Change the frequency to 5 MHz as follows:

Press the

Freq

button on the front panel to select the Frequency parameter

in the Quick View area.

Press the

number key.

Press the

button to set the units to MHz.

Press the

Setting

button to exit the frequency setting.

Navigation quick tip.

You can set the frequency parameter without changing the

units as follows: press the

Freq

button, use the general knob to increase/decrease

the value, and then press the

Setting

button.

Change the amplitude for the Type N output by 1 dBm as follows:

Press the

Ampt

button on the front panel to select the Type-N output

amplitude parameter in the Quick View area.

Press the

Enter

button to set the units to dBm.

Use the general knob to increase the amplitude by 1 dBm.

Press the

Setting

button to set and exit the amplitude setting.

Navigation quick tip.

You can use the number keys and unit keys to set the

amplitude parameter value and units as follows: press the

Ampt

button, press the

desired number key, press the desired unit key, and then press the

Setting

button.

Change the amplitude for the BNC output by 0.001 V as follows:

Select

RF/LF

from the main menu.

Select

LF Amplitude

from the submenu.

Press the 5 number key.

Press a unit key to set the LF Amplitude to Vpp or Vrms.

Press the

k/m

button to set the units to mV.

Use the general knob to increase the amplitude by 1 mV.

Press the

Setting

button to set and exit the amplitude setting.

Modulation presets

functional check

Your instrument includes a number of modulation presets that automatically
con

gure the generator to produce modulation waveforms for a number of

different communications protocols, such as GSM, DECT, and TETRA. Do the
following to see how this preset type is enabled.

Press the

Freq

button and then set the frequency to 935.2 MHz.

Select

Mod

from the Main menu.

Select

Mod Type

from the

Mod

submenu.

TSG4100A Series RF Signal Generators User Manual

Содержание TSG4102A




































































































Результаты поиска

Содержание TSG4102A

Отзывы:

Похожие инструкции для TSG4102A

Бренды по названию

Популярные бренды

Tektronix TSG4102A, Руководство пользователя

Результаты поиска

Содержание TSG4102A

Отзывы:

Похожие инструкции для TSG4102A

Бренды по названию

Популярные бренды