Tektronix TLA7000 Series Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 121

background image

Basic Installation

Checking the P624x

Oscilloscope Probes

(Optional)

Connect the oscilloscope probes to the Probe Compensation connector on the
front panel of the oscilloscope modules. You can then run the Calibrate Probe
function in each vertical setup page for the module.

Checking the P647x

Pattern Generator Probes

(Optional)

Set up a simple pattern generator program to output a signal to the probes.
Connect an oscilloscope probe to the probe outputs and verify that the signal is
present at the probe outputs.

Checking the TLA7000

Mainframe (Optional)

To check the mainframe diagnostics not covered by the TLA Application software,
run the TLA7000 Mainframe Diagnostics located under the Windows Start menu
(Start/Programs/Tektronix Logic Analyzer/TLA Mainframe Diagnostics). Exit the
TLA Application before running the external diagnostics.

Backing Up User Files

Back up your user

fi

les on a regular basis. Use the Windows back up tools or copy

the

fi

les to another media. Always keep a backup copy of

fi

les that you access

on a regular basis.

Removing the Replaceable Hard Disk Drives

CAUTION.

To avoid permanently damaging the replaceable hard disk drive, do

not remove it while the instrument is powered on. Always power off the instrument
before removing the hard disk drive.

1.

Verify that the instrument is powered off.

2.

Open the access door (TLA7PC1 only).

3.

Pull out the lever (TLA7PC1), or unscrew the locking thumbscrews
(TLA7012). (See Figure 47.)

4.

Pull on the replaceable hard disk drive cartridge to remove it from the chassis.

52

TLA7000 Series Logic Analyzers Installation Manual

«
...
68
69
70
71
72
...
»

Содержание TLA7000 Series


























































































































Отзывы:

Нет отзывов

Похожие инструкции для TLA7000 Series

Бренд: OfiTE Страницы: 24

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: Badger Meter Страницы: 56

ModMAG M Series

Бренд: Badger Meter Страницы: 4

Бренд: ECO Sensors Страницы: 22

Бренд: ECO Sensors Страницы: 7

Бренд: F&F Страницы: 24

NANOCOLOR Advance

Бренд: Macherey-Nagel Страницы: 45

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 12

Бренд: QUBINO Страницы: 2

Бренд: T&D Страницы: 2

Бренд: T&D Страницы: 2

Бренд: Sage Страницы: 68

Бренд: PITSID Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды