Tektronix TLA7000 Series Скачать руководство пользователя страница 100

Страница: 100 / 121

Restoring and Reinstalling Software

NOTE.

Be sure to select the proper .lod

le for each module. Note the slot number

in the title bar so that you select the correct module for the .lod

le.

Table 7: TLA

rmware

les

Module type

.lod

TLA7Nx, TLA7Px, TLA7Qx logic analyzer
modules

TLA7NPQ.lod

TLA7Lx and TLA7Mx logic analyzer modules

TLA7LM.lod

TLA7Dx and TLA7Ex oscilloscope modules

FirmwareDSO.lod

16.

Click OK. When asked to con

rm your action; click Yes.

NOTE.

The program will not allow you to load

rmware to an incompatible

module. For example, the program will not load oscilloscope

rmware to a logic

analyzer module.

The program loads the

rmware for each module one at a time. The process

may take several minutes per module.

17.

When the upgrade is complete, exit the program.

18.

Turn off the logic analyzer and disconnect the power cord.

19.

Remove the module from the instrument and remove the jumper from the
Flash programming pins on the rear of the module. Keep the jumper for
future updates.

20.

Locate the big label on the side of the module.

21.

Record the

rmware version that is printed on the label. You will need this

information to see that the

rmware version matches the label.

22.

Reinstall the module in the mainframe and power on the mainframe.

23.

After the logic analyzer completes the power-on diagnostics, select System
Properties from the System menu.

24.

Click the module tab (for example, LA1).

25.

Verify that the

rmware version for the selected module matches the version

on the label that you recorded in step 21.

26.

If the

rmware versions do not match, power down the mainframe, remove

the module from the mainframe and update the label.

TLA7000 Series Logic Analyzers Installation Manual

Содержание TLA7000 Series


























































































































Результаты поиска

Содержание TLA7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Tektronix TLA7000 Series, Руководство по установке

Результаты поиска

Содержание TLA7000 Series

Отзывы:

Бренды по названию

Популярные бренды