manualshive.com logo in svg

Tektronix SD-44, Инструкция по эксплуатации, Страница: 15 / 30

Поделиться
Скачать
Tektronix SD-44 Скачать руководство пользователя страница 15

SD-44 Instruction Manual

7

Operating Basics

To prolong the life of the SD-44 O/E converter observe the following handling,
cleaning, and operating instructions.

Handling

Handle the SD-44 O/E converter carefully at all times.

CAUTION.

 To avoid damaging the SD-44 O/E converter, take the following

precautions:

Do not drop the O/E converter since damage and misalignment of the photo-
diode optical assembly can result. Store the O/E converter in a secure location
when not in use.

Replace the protective caps on the input and output connectors when the O/E
converter is not in use.

Cleaning Optical Connectors

Small dust particles and oils can easily contaminate optical connectors and
reduce or block the signal. Take care to preserve the integrity your connectors by
keeping them free of contamination.

CAUTION.

 To prevent loss of optical power or damage to the optical connectors,

keep the connectors clean at all times.

When cleaning the connectors with a swab, use gentle circular motions. Use only
high quality cleaning supplies that are non-abrasive and leave no residue.

To reduce the need for cleaning, immediately replace protective caps on the
optical connectors when not in use.

Содержание SD-44































Отзывы:

Нет отзывов