Tektronix RSA3303B Скачать руководство пользователя страница 21

Страница: 21 / 79

Installation

Figure 7: Spectrum of the RSA3408B calibration signal (100 MHz, about -20 dBm)

Check the center frequency and peak amplitude using the marker:

Press the

PEAK

key on the front panel to place the marker on the peak.

(See Figure 7.)

Check the marker readouts on screen. The frequency should be 100 MHz
(RSA3408B) or 50 MHz (RSA3300B) and the amplitude should be
approximately -20 dBm.

Press the

MARKER SETUP

key on the front panel and then the

Markers

side key to select Off. Check that the marker disappears.

Check the RBW (Resolution Bandwidth) while changing the span setting.

Press the

SPAN

key on the front panel.

Con

rm that the span is 36 MHz (RSA3408B) or 15 MHz (RSA3300B)

and the RBW is 100 kHz (RSA3408B) or 80 kHz (RSA3300B) in the
setup display on the upper part of the screen. (See Figure 8.)

RSA3303B, RSA3308B, and RSA3408B User Manual

Содержание RSA3303B
















































































Результаты поиска

Содержание RSA3303B

Отзывы:

Бренды по названию

Популярные бренды

Tektronix RSA3303B, Руководство пользователя

Результаты поиска

Содержание RSA3303B

Отзывы:

Бренды по названию

Популярные бренды