background image

Connect

WARNING

To prevent electric shock that could result in injury or 

death, NEVER handle a switching card that has power 

applied to it.

Before installing or removing a switching card, make 

sure the instrument is turned off and disconnected 

from line power. Even when the instrument is powered 

off, hazardous voltages may be present in signal 

cables attached to the switch cards. Always disconnect 

all cables before removing or installing a switch card.
If the switching card is already connected to a device 

under test (DUT), make sure power is removed from all 

external circuitry.

NOTE

For inexperienced users, disconnect DUT and external 

circuitry from switching cards. This allows you to exercise 

safe close/open operations without the dangers associated 

with live test circuits.

WARNING

Slot covers must be installed on unused slots to 

prevent personal contact with high-voltage circuits.

To install a switching card in a Series 3700A 

instrument:

1.  Turn the instrument power off.

2.

 Position the instrument so that you are facing the

rear panel.

WARNING

As described in the International Electrotechnical 

Commission (IEC) Standard IEC 664, the Series 3700A 

switch cards are Installation Category O and must not 

be connected to mains.

3.

 Disconnect the power line cord and any other cables

connected to the rear panel.

4.  Remove the slot cover plate from the slot. Retain the

plate and screws for future use.

Содержание Keithley 3700A Series



















Отзывы: