background image

 

8

Model 4000 WPP Upgrade

Version 6.0R2 

 

DSK Matte Fills and Borderline Mattes

 

 

Flat matte fills and borders remain unchanged from previous software 
versions.

 

 

USER DEF WASH uses the PGM/PST secondary wipe generator to 
wash between the Matte 1 and Matte 2 generators.

 

 

To avoid conflicts between the PGM/PST and M/E 1 decks, the SEC 
WIPE WASH (which uses M/E 1’s secondary wipe generator) has been 
disabled for key fills and borderline mattes on DSK 1 and DSK 2.

 

 

Since the PGM/PST PRI wipe is used for transitions on the PGM bus, 
copying to the PGM PST PRI wipe generator is not allowed. Therefore, 
key copies from M/Es using a primary wipe generator (such as 
primary wipe washes and primary wipe INH masks) to a DSK will 
result in an error. However, with the new release of the software, keys 
using only a secondary wipe generator can be copied to the DSKs.

 

Note

 

Remember that pressing USER DEF WASH on the PGM/PST matte panel actu-
ally activates the PGM/PST secondary wipe generator for the purpose of wash 
operations.

 

Matte and Wash Operator’s Summary for Model 4000-3 with WPP

 

 

All Matte and Wash controls for Key Matte Fills are stored in the [DSK] 
level for E-MEM recall,

 

 

All Matte and Wash controls for Borderline Matte Fills are stored in the 
[DSK] level for E-MEM recall,

 

 

All Matte and Wash controls for PGM/PST Primary Wipe Border are 
stored in the [DSK] level for E-MEM recall,

 

 

For both Background Matte and Wash controls: User Wash is stored in 
[MISC] and [BKGD] levels for E-MEM recall, and

 

 

Secondary Wipe Wash is stored in [MISC], [BKGD], and [M/E1] levels 
for E-MEM recall.

 

 

The following describes Background Matte and Wash level controls:

 

 

[MISC] level: User Wash Softness and User Wash Offset

 

 

[BKGD] level: Matte Wash Colors and User/Sec Wipe Wash Selection

 

 

[M/E1] level: All Sec Wipe Generator controls

 

Note

 

Attempts to copy or swap a primary wash matte to a DSK key or border fill will 
instead result in a secondary wash. Two consecutive swaps will change the 
source matte to a secondary wash.

Содержание 4000-3











Отзывы: