manualshive.com logo in svg

Tektronix 071-0060-00, Инструкция по эксплуатации

Поделиться
Скачать
Tektronix 071-0060-00 Скачать руководство пользователя страница 24

Performance Verification

ORR24 Instruction Manual

15

10. Without moving the optical attenuator from the position in the previous step,

disconnect the output fiber of the optical attenuator from the inline adapter
with the ORR24 and insert the optical attenuator output into the optical
power meter.

11. Adjust the optical power meter to the calibrated wavelength setting of

1550 nm. Note the absolute power displayed. The 1550 nm conversion gain
in units of V/mW

opt

 is

((200 

mW) / (measured 1550 power)) 

×

 (1310 nm conversion gain)

12. Record the 1550 nm conversion gain on the test record.

Noise Equivalent Power

Power the ORR24 under test using the digital sampling oscilloscope.

1. Zero the RF power meter.

2. Connect the ORR24 output channel to the RF power meter using a 1 GHz

low-pass filter in series.

3. With the dust cover on the input to the ORR24, the RF power meter should

read less than

[15 pW

opt

ń Hz

Ǹ

  1 GHz

Ǹ

  (measured conversion gain in VńW

opt

)]

2

50

W

+ 4.5   10

–15

  (measured conversion gain in VńW

opt

)

2

+ W

elec

(

NOTE :

V

ńW

opt

+ VńmW

opt

  1000)

4. Record the calculated and measured results on the test record.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 071-0060-00

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды