Teknetics T 2+ Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 40

Teknetics T 2+ Скачать руководство пользователя страница 23

TEKNETICS

Comprehensive Operating Manual & Guide to Metal Detecting

23

CAPABILITIES AND LIMITATIONS (continued)

GROUND CANCELING

To achieve maximum depth in both the ALL METAL and DISCRIMINATION Modes, as well as

when using the PinPoint feature, the

T

2+

offers the ability to cancel ground minerals either by

manual adjustment, or automatically using the FASTGRAB™ feature (see p.11).

If you do not perform the ground canceling operation, the Discrimination Mode will usually still

work fairly well, but the ALL METAL Mode will not. The Pinpoint feature can be used for

pinpointing objects at moderate depth in most soils without prior ground-canceling.

The internal computer will not automatically cancel salt water, so when detecting on wet ocean

beaches, ground cancellation must be done manually.

DISCRIMINATION

Discrimination refers to a metal detector’s ability to ignore metal objects in selected categories,

especially iron and aluminum. This makes searching much more pleasant in an area with a lot

of metal trash. The

T

2+

offers a wide variety of discrimination features which you can select

according to the search conditions and your personal preference.

DEPTH READING

The estimated Depth Reading displayed when engaging the PinPoint feature is based on the

strength of the signal. It is calibrated for typical coin-sized objects. Small objects will read

deeper than they actually are, and large objects will read shallower than they actually are.

AIR TESTING

There may be times when you want to test or demonstrate the metal detector without

sweeping it over the ground, for instance, if not fully assembled, or if you are indoors. To air

test, place the searchcoil in a spot where the detector is stable and more than two feet away

from any large masses of metal, including the reinforcing steel usually present in concrete. If

you are wearing a wristwatch or jewelry on your hand or arm, remove it. Then, test or

demonstrate by waving metal objects over the searchcoil; wave objects briskly, several inches

over the top of, and parallel to, the searchcoil.
Ground cancellation cannot be tested or demonstrated in air unless you happen to have

appropriate specimens of iron minerals available.

SWEEP SPEED

The

T

2+

is noted for its quick response. This gives it unsurpassed ability to locate and identify

good targets surrounded by trash. It also permits the user to sweep the searchcoil quickly in

order to cover more ground with very little risk of losing targets. In general, if you are

searching an area where the desirable targets are more than 8 to 10 inches deep, a faster

sweep speed will detect to a greater depth and yield more accurate Target-IDs.

CHECKING A TARGET

In order to most accurately verify a detected target with most other metal detectors, users will

narrow their sweep and loiter over the top of the target. The

T

2+

is different. The

T

2+

’s quick

response and advanced signal sampling system produces the most accurate Target-IDs with

deliberate (shoulder width) sweeps all the way across the target, even if there are other targets

nearby. If you use a non-standard sweep method or speed to check targets with the

T

2+

, the ID’s

will bounce around more and you run the risk of misidentifying the target.

«
...
21
22
23
24
25
...
»

Содержание T 2+









































Отзывы:

Нет отзывов