PRO-TEK
G3
CHUCK
QUICK START
INSTRUCTION MANUAL
Thank you for purchasing our P
RO
-
TEK G3
Chuck – a new
premium
addition to our Nova
woodturning chuck range with advanced features to enhance your chuck performance.
It provides a versatile and easy method for fast and secure work holding for all face
turning – bowls, egg cups, vases, boxes, goblets and an endless variety of similar projects.
OPENING AND CLOSING OF JAWS
MOUNTING THE PRO-TEK
G3
CHUCK
ON THE LATHE
There are two configurations available for the P
RO
-T
EK G3
chuck:
•
Insert model -Requires an insert for chuck to be mounted on the lathe. See full manual
online for a list of lathe spindle thread inserts available.
•
Direct Thread models: 1” 8TPI & M33 Eurolock
1.
If the chuck is an insert model,
ensure the insert is bottomed out
in the chuck body before mounting
on the lathe.
2.
For Both Insert & Direct Thread
model: Wind the chuck on the
lathe spindle until the chuck comes
firmly in contact with the
bearing/spindle shoulder with no
gaps between.
3.
Place red thread protector washer
into the M6 Threaded hole. Then
wind the M6 grub screw in position
and tighten with M3 Allen head
wrench (provided) to prevent the
chuck from loosening on lathe
spindle.
Using the Nova M33 Eurolock Chuck with Locking Ring (Only applicable to EU model)
Step 1:
Tighten the EU chuck to the spindle on the
lathe, make sure the rings on the spindle and
chuck have been clamped. Note: EU Lock Ring
is provided with the lathe
Step 2
:
Put the lower part of locking ring under the
clamped rings.
Step 3
:
Put upper part of the locking ring to the
clamped rings as well.
Step 4
:
Using the Allen key to tighten up two bolts on
the locking ring.
YOUR SAFETY
Keep these instructions in a safe place for future reference.
WARNING:
This chuck is capable of contributing to serious injury (as with any other power
tool accessory) if this manual guidance is not followed or if it is used improperly on the
lathe. Read and understand also the lathe owner's manual. If you do not have a manual,
contact the supplier of your lathe to obtain one before using the lathe and chuck. User
must be professionally trained to use this chuck. Vocational school courses or other expert
tuition is recommended.
As with other work holding methods, an extremely cautious and sensible approach is
necessary. With the PRO-TEK
G3
Chuck it is not possible to give exact directions as to the
amount of tightening pressure required for adequate work holding or approved chisel
cutting techniques. Follow closely strict guidelines in this manual for different jaw types
on wood blank diameters and length, plus strictly follow recommended lathe speeds.
Safe Operation:
Eye Protection:
Woodturning operations can result in objects being thrown into your eyes
which can result in severe eye damage. Protective eye wear must be used at all times.
Everyday vision wear is not protective eye wear. We recommend a full-face shield. Always
wear eye protection which complies with current ANSI Standard Z87 (USA)
Noise Protection:
Use ear plugs or ear defenders. Particularly if the noise exceeds 85dB.
Exposure to high levels of noise can lead to hearing problems.
Dust Protection:
Use respiratory protective equipment (dust mask, portable respirator
device). Exposure to high levels of irritating dust when turning or sanding hardwoods, soft
woods and manufactured composite boards (MDF) can result in serious health problems.
In addition, adequate workshop dust extraction must be used.
Chuck is properly secured on lathe spindle:
Follow mounting instructions for your lathe
for faceplates and other spindle fixtures. Do not rotate chuck under power unless
workpiece is firmly clamped.
WARNING: LATHE SPEED:
Excessive speed is a serious lathe hazard. Always turn at the
slowest speed possible. Ideal speed will vary with wood blank size. The larger the blank
the slower the speed. Consult your lathe manual or lathe information plate for speed
guidelines. Do not attempt to use the chuck unless the recommended lathe speeds to size
of wood blank are known. In addition, you must strictly follow the maximum speed limits
set out in the operating section of this manual. Do not exceed them under any
circumstances.
CHECK WORKPIECE:
Examine wood blank carefully before mounting on chuck/lathe.
Only mount wood that has no cracks, splits, holes or any other weaknesses (e.g. rotten or
spongy sections). Do not use poorly jointed or laminated wood. Irregular or out of balance
stock needs to be turned at the slowest possible speed until it is in balance.
Make sure wood is clamped firmly. Follow mounting instructions for different gripping
modes and jaw types. In the expansion mode do not use undue force or jaws may split the
wood.
Do not exceed maximum guidelines in this manual for wood blank diameters/length set
out in this manual for different modes and jaw types.
Check wood is securely held in chuck, before operation. Check grip by vigorously
wrenching wood blank back and forth. If any loosening occurs, re-examine holding area
for adequate grip (Following mounting guidelines) and any damage to holding area. Rotate
manually to make sure of clearance before switching power on.
DUPLICATOR OR JIGS
: Do not use chuck for work holding with a duplicator or jigs.
Safe Practice:
CHISEL USE:
Use only hand held woodturning chisels to shape wood being held in chuck.
Use the recommended chisel for the job. Use safe and commonly approved techniques.
WARNING:
Never attempt to place hands on a moving chuck on a lathe. Wait for the chuck
to come to a complete stop before hands are anywhere near the chuck. Trying to grab at
a moving chuck could result in SERIOUS INJURY. Jaw Slides: For safe operation do not
extend the jaw slides beyond the chuck body under any circumstances.
Wherever possible stand to one side of the revolving wood.
WEAR SUITABLE CLOTHING:
Do not wear any loose clothing, neck ties, gloves, bracelets,
rings or other jewellery that could get caught in moving parts. Wear protective hair
covering to contain long hair.
DRUGS, ALCOHOL, MEDICATION:
Do not operate chuck or lathe while under the influence
of drugs, alcohol or any medication.
KEEP CHILDREN AND VISITORS AWAY:
All children and visitors should be kept safe
distance from the work area.
ATTACHING AND REMOVING JAWS
The standard P
RO
-T
EK G3
chuck comes included with a set of P
RO
-T
EK
50mm (#6075)
add-on jaws.
The jaws must be properly attached on the chuck to function as intended.
Before installation, ensure the jaw slide top surfaces are clear of any dust or debris
before attaching the jaws on the chuck.
Follow the steps shown below to attach the jaws on the chuck:
Loosely attach the jaw segments on the jaw
slide with the Nova Star head screws
included and firmly close the jaws to make
sure no light is visible between the jaw
segments.
Note:
Ensure the number indented on the
jaw edge matches the jaw slide number
Firmly tighten the Nova Star head screws
with the Nova Star head T-bar handle
included.
Loosen and remove the Nova Star head
screws when removing the jaws from the
chuck.
No light visible between jaws
Open
Close
Place red thread protector washer into
M6 threaded hole. Then wind the M6
grub screw in place and tighten
Make sure there
is no gap
all around this
contact line
Insert
bottomed out
(If insert
version)
