21
Installation place
Install the machine in such a way so that ventilation openings are not obstructed (forced circulation).
Do not allow aggressive steam, dust, humidity etc., inside the machine.
Connecting the machine to the supply line
Install the plug which meets standards on the feeding cable. The plug must be equipped with ground
tip, which must be connected with yellow-green cable. Prepare the receptacle which meets standards.
The receptacle must be equipped with a fuse or an automatic circuit breaker. From table 1 determine
recommended nominal of the fuse at maximum rated consumed current and rated line voltage.
Table 1
Before connecting ensure that voltage, indicated on the machine nameplate, complies with the voltage
and frequency of the mains.
Connecting welding cables
Any connection to the welding circuit must be performed when the machine is disconnected from the
supply line.
Welding cable with electrode holder
is connected to the positive pole (+) (see «Welding»).
Cable with functional terminal is connected to the negative pole (-), its other end is connected to the
piece to be welded or operating area as close to the welding seam as possible.
WARNING! Connected cables must be inserted securely in the terminals, which will
ensure good contact. Loose connections will lead to overheating, timely wear, loss
of efficiency and damage to the terminals.
Do not use welding cables of more than 5 m in length.
Never use metallic constructions which are not the part of the piece to be welded instead of cable with
functional terminal, as this will violate safety and lead to poor welding.
Welding
WARNING!
Most welding electrodes are connected to the positive pole, although some
types have to be connected to the negative pole. It i
s important to follow manufacturer’s
instructions on the package of the electrodes, as they indicate right polarity of the welding electrode as
well as the most suitable current for welding operations.
Adjust welding current according to diameter of used electrode and according to type of welding seam.
Below is the table of admissible current according to diameter of the electrode:
Electrode diameter, mm
Welding current
, А
Min
Max
1,6
25
50
Fuse nominal, A
Welding current, A
Receptacle
capacity, A
Cable section, mm
16
140
16
10
16
160
25
10-16
25
180
36
16
25
200
36
16-20
25
250
36
20-25
36
300
36
25
Содержание TWI-250 DB
